You are here: Home > Fire Alarms >

Fire Accessories for Fire Alarm Systems

>

Accessories for Fire Alarm Systems

We found 44 results matching your criteria.
At Security Store USA you'll find accessories to maintain your existing fire system and to meet tough fire department standards. Browse the array of fire accessories, including connector card for amplified speakers, PAM relays, bases for smoke detectors, transceivers and more. You'll find fire equipment and accessories to  enhance your existing fire system or replace old fire equipment components, so that the level of fire protection you offer is at its best.
Sort By:
Page of 4
AlarmNet 7845CF Control Channel Cellular Subscriber Transceiver AlarmNet 7845CZF Control Channel Cellular Subscriber Transceiver

Designed as a cellular backup for fire applications, Honeywell’s 7845CF takes advantage of the latest advances in Control Channel Cellular design—offering virtually limitless coverage at an affordable price.

The 7845CF eliminates the need for a secondary dedicated phone line and helps increase recurring monthly revenue. It replaces the 7835CFPK when used with an ADEMCO control in ECP mode. The included 6V, 4.5A hour battery and internal battery charger provide more than 24 hours of backup time.

All signals are delivered to the AlarmNet Control Center, which routes the information to the appropriate central station. The AlarmNet Control Center is fully redundant and monitored 24 hours a day, seven days a week.

AlarmNet has the ability to route messages using the AlarmNet “A”, AlarmNet “M”, AlarmNet “i” and 800 plus networks; all of which provide true redundancy and virtually guarantee message delivery.

Includes: Cell radio, red cabinet, backup battery and battery cable, transformer, antenna, wiring for connecting antenna.

Features:

  • Built-in indicators make installation easy
  • Designed as secondary connection for commercial fire
  • Eliminates a dedicated phone line
  • Increases recurring revenue
  • Low battery detect and reporting
  • Nationwide coverage
  • Multiple modes of operation
  • Transmission in full contact ID or ADEMCO High Speed
  • Timed status check-in for radio link supervision
  • Antenna tamper detect
  • DC line voltage loss reporting
  • Multiple registration and programming options
  • Tamper protection
  • In excess of 24 hours of battery backup

    RECOMMENDED REPLACEMENT FOR 7835CFPK

  • Designed as a cellular backup for fire applications, Honeywell’s 7845CZF works with any product that provides outputs via contact closure or voltage trigger. The 7845CZF takes advantage of the latest advances in Control Channel Cellular design—offering virtually limitless coverage at an affordable price.

    The 7845CZF eliminates the need for a secondary dedicated phone line and helps increase recurring monthly revenue. It replaces the 7835CFPK when zone inputs are required. The included 6V, 4.5A hour battery and internal battery charger provide more than 24 hours of backup time.

    All signals are delivered to the AlarmNet Control Center, which routes the information to the appropriate central station. The AlarmNet Control Center is fully redundant and monitored 24 hours a day, seven days a week.

    AlarmNet has the ability to route messages using the AlarmNet “A”, AlarmNet “M”, AlarmNet “i” and 800 plus networks; all of which provide true redundancy and the highest reliability in message delivery.

    INCLUDES: Cell radio, red cabinet, backup battery and battery cable, transformer, antenna, wiring for connecting antenna

    Features:

  • Built-in indicators make installation easy
  • Designed as secondary connection for commercial fire
  • Eliminates a dedicated phone line
  • Increases recurring revenue
  • Low battery detect and reporting
  • Nationwide coverage
  • Six supervised zones via contact closure or voltage triggers
  • Seven reporting zones
  • Inverted operation
  • Multiple modes of operation
  • Fault output
  • Antenna tamper detect
  • Timed status check-in for radio link supervision
  • Multiple registration and programming options
  • Tamper protection
  • In excess of 24 hours of battery backup
  • DC line voltage loss reporting
  • Commercial Products Group  WPSBBR Back Box Weatherproof for the RSSWP Series Red Commercial Products Group 169170A05  Cover Plate for Mini Sounder
    Commercial Products Group  WPSBBR Back Box Weatherproof for the RSSWP Series Red Commercial Products Group 169170A05  Cover Plate for Mini Sounder
    Commercial Products Group ASRBKS124P - Trouble Relay Module PS5A/B Commercial Products Group CMXC - Ceiling mount for FSEX
    Commercial Products Group ASRBKS124P - Trouble Relay Module PS5A/B

    Commercial Products Group CMXC - Ceiling mount for FSEX

    Commercial Products Group HSC224RA - 2 -Wire Base w/ Relay - Replaces HSC224R Commercial Products Group NS6-220  6" Base, 2-Wire, 93-Mililamps HIDICKI
    Commercial Products Group HSC224RA - 2 -Wire Base w/ Relay - Replaces HSC224R
    Description
    The NS6 and NS4 Series is designed specifically for use with Conventional Models SIJ-24 Ionization Smoke Detector, SLR-24 Photoelectric Smoke Detector, SLR- 24H Photoelectric with Heat Smoke Detector, SLR-835 Photoelectric Smoke Detector, SLR-835H Photoelectric Smoke Detector with heat, or DCD-135/190 Fixed Temperature/Rate-of-Rise Heat Detector. The base is an electronics free 6" base featuring a plastic tamper-lock lug. Each base is equipped with a resistor. The NS4 base is a 4" version of the NS6 base.

    Models HSC-224R, HSC-220R and HSC-221R are designed specifically for use with the Conventional Models SIJ-24, SLR-24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190. The HSC-(X)R series is a 5" base with two sets of Form "C" relay contacts.
     
     Models HS-224R, HSC-220R and HSC-221R are also approved for use with the previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and the DFE 135/190. The HSC-4R is designed specifically for 24 volt 4 wire applications using Conventional Models SIJ-24, SLR- 24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190.

    The 6" diameter base is current limited. Relay contact place a direct short occurs across the loop when the detector is actuated. Model HSC-4R is also approved for use with previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and DFE 135/190.
     
    The HSC-L Base Series is designed specifically for use with the Fixed Temperature Heat Detector Models DFE-135/190. The HSC-L Series is a 6" base featuring a current limiting resistor, latching annunciator output and a latching circuit so the alarm LED will remain lit until the control panel has been reset.

    Features
  • 4” or 6” base
  • 2 or 4 wire operation
  • 4 wire current limited relay
  • 2 wire latching LED base
  • Commercial Products Group NS6-221 - 6" Base for Smoke Head Commercial Products Group NS6-224 - 2-Wire Base 24VDC 6" Pulls 43MA
    Description
    The NS6 and NS4 Series is designed specifically for use with Conventional Models SIJ-24 Ionization Smoke Detector, SLR-24 Photoelectric Smoke Detector, SLR- 24H Photoelectric with Heat Smoke Detector, SLR-835 Photoelectric Smoke Detector, SLR-835H Photoelectric Smoke Detector with heat, or DCD-135/190 Fixed Temperature/Rate-of-Rise Heat Detector. The base is an electronics free 6" base featuring a plastic tamper-lock lug. Each base is equipped with a resistor. The NS4 base is a 4" version of the NS6 base.
    Models HSC-224R, HSC-220R and HSC-221R are designed specifically for use with the Conventional Models SIJ-24, SLR-24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190. The HSC-(X)R series is a 5" base with two sets of Form "C" relay contacts. Models HS-224R, HSC-220R and HSC-221R are also approved for use with the previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and the DFE 135/190.
    The HSC-4R is designed specifically for 24 volt 4 wire applications using Conventional Models SIJ-24, SLR- 24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190.
    The 6" diameter base is current limited. Relay contact place a direct short occurs across the loop when the detector is actuated. Model HSC-4R is also approved for use with previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and DFE 135/190.
    The HSC-L Base Series is designed specifically for use with the Fixed Temperature Heat Detector Models DFE-135/190. The HSC-L Series is a 6" base featuring a current limiting resistor, latching annunciator output and a latching circuit so the alarm LED will remain lit until the control panel has been reset.
    Features
  • 4” or 6” base
  • 2 or 4 wire operation
  • 4 wire current limited relay
  • 2 wire latching LED base
  • Description
    The NS6 and NS4 Series is designed specifically for use with Conventional Models SIJ-24 Ionization Smoke Detector, SLR-24 Photoelectric Smoke Detector, SLR- 24H Photoelectric with Heat Smoke Detector, SLR-835 Photoelectric Smoke Detector, SLR-835H Photoelectric Smoke Detector with heat, or DCD-135/190 Fixed Temperature/Rate-of-Rise Heat Detector. The base is an electronics free 6" base featuring a plastic tamper-lock lug. Each base is equipped with a resistor. The NS4 base is a 4" version of the NS6 base.

    Models HSC-224R, HSC-220R and HSC-221R are designed specifically for use with the Conventional Models SIJ-24, SLR-24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190. The HSC-(X)R series is a 5" base with two sets of Form "C" relay contacts.
     
    Models HS-224R, HSC-220R and HSC-221R are also approved for use with the previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and the DFE 135/190.The HSC-4R is designed specifically for 24 volt 4 wire applications using Conventional Models SIJ-24, SLR- 24V, SLR-24H, SLR-835, SLR-835H or DCD-135/190.

    The 6" diameter base is current limited. Relay contact place a direct short occurs across the loop when the detector is actuated. Model HSC-4R is also approved for use with previous Conventional Models SIH-24F, SLK-24F, SLK-24FH and DFE 135/190.

    The HSC-L Base Series is designed specifically for use with the Fixed Temperature Heat Detector Models DFE-135/190. The HSC-L Series is a 6" base featuring a current limiting resistor, latching annunciator output and a latching circuit so the alarm LED will remain lit until the control panel has been reset.

    Features
  • 4” or 6” base
  • 2 or 4 wire operation
  • 4 wire current limited relay
  • 2 wire latching LED base
  • Commercial Products Group PAM 1 - Single End of Line Relay Commercial Products Group PAM 2 - End of Line Power Supervisory Relay 24V
    The PAM Series Relays are encapsulated multi-voltage devices with “flying” leads that offer versatile, reliable performance in a convenient package. Several of the versions contain a red LED which indicates when the relay coil is energized. The PAM Series Relays are packaged with a self-tapping screw and a piece of double sided tape for easy installation almost anywhere. The relays are also packaged with wire-nuts to aid installation.
     
     PAM Relays are ideal for applications where remote relays are required for control or status feedback. They are suitable for use with HVAC, Temperature Control, Fire Alarm, Security, Energy Management, Lighting Control Systems and Building Automation Systems.

    The PAM-2 Relay provides 7.0 A form “C” contacts. The relay may be energized by one of two input voltages: 12VDC or 24VDC. The input voltages are polarity-sensitive and diode-protected. PAM-2 Relays contain a red LED which indicates when the relay coil is energized.
    The PAM Series Relays are encapsulated multi-voltage devices with “flying” leads that offer versatile, reliable performance in a convenient package. Several of the versions contain a red LED which indicates when the relay coil is energized. The PAM Series Relays are packaged with a self-tapping screw and a piece of double sided tape for easy installation almost anywhere. The relays are also packaged with wire-nuts to aid installation.
     
     PAM Relays are ideal for applications where remote relays are required for control or status feedback. They are suitable for use with HVAC, Temperature Control, Fire Alarm, Security, Energy Management, Lighting Control Systems and Building Automation Systems.

    The PAM-2 Relay provides 7.0 A form “C” contacts. The relay may be energized by one of two input voltages: 12VDC or 24VDC. The input voltages are polarity-sensitive and diode-protected. PAM-2 Relays contain a red LED which indicates when the relay coil is energized.
       
     
    Accessories for Fire Alarm Systems
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please