Home > Shop Brands > Honeywell Security & Communications > Honeywell Security Sensors > Glassbreak Detector >

 

Ademco ASC-SS1 Glassbreak Shock Sensor, 2-wire - ASCSS1



Ademco ASC-SS1 Glassbreak Shock Sensor, 2-wire - ASCSS1


 

Our Price : $10.85

UPC Code: 781410181755

Product Code: 9645

Qty:

Description
 

The ASC-SS1 shock sensor protects all types of glass: plate, wired, tempered, and laminated. The sensor will protect the glass within an 8 feet radius from the sensor for glass up to 1/4 inch thick. The ASC-SS1 mounts directly to the glass surface and is wired to a two wire powered protective loop.

Wiring
The ASC-SS1 shock sensor is a two wire electronic device which draws minimal current (< 1mA) from the protective loop. When glass is broken, the sensor provides a normally-closed solid-state output (circuit opens on alarm) which is not polarity sensitive. The sensor employs transient suppression devices to protect against lightning.

The ASC-SS1 shock sensor does not require a processor.

The ASC-SS1 shock sensor may be wired in series with multiple sensors. Care should be taken to ensure that the total resistance of the sensors in series does not exceed the capabilities of the alarm control panel.

Testing
To test the shock sensor, hit the protected glass on the corner furthest from the sensor (see diagram) using a blunt plastic or hard rubber object. This impact should create enough energy for the sensor to generate an alarm condition. Actually breaking the glass would create more energy than the test, so if the test impact causes the sensor to generate an alarm, protection is assured.

If the unit is tested in the alarm circuit, tripping the detector should trip the alarm panel. An alternate test method is to connect the sensor to an ohm meter and watch the resistance (less than 20Ω when not in alarm) increase to greater than 1MΩ for at least 1 second during an alarm condition.

Installation
The ASC-SS1 shock sensor must be mounted in a corner of the glass. For best performance, do not mount the sensor closer than 1" from the window frame.

Shock sensors mount with double coated acrylic foam tape designed to resist the types of environmental stresses the shock sensor will experience after installation.

Features:
  • Mounts directly on glass surface
  • Protects all glass types: plate, tempered, laminated and wired
  • Outstanding false alarm immunity
  • Epoxy sealed against moisture and corrosion

    Specifications:
  • Loop Voltage: 3VDC min. to 20 VDC max.
  • Loop Current: 100mA max.
  • Power Requirements: Less than 1mA
  • Transient Suppression: 600 W for 1 mS
  • Alarm Output Type: Normally-closed solid-state output, non-polarized
  • Alarm Output Resistance:
    - 20Ω max. (closed/non-alarm condition)
    - 1MΩ min. (open/alarm condition)
  • Alarm Output Timing: Open for 1 second min. during an alarm condition
  • Operating Temperature: 0oF ~ +130oF (-18oC ~ 55oC)
  • Case Dimensions: 1.4" L x 0.95" W x 0.3" D
  • Wiring Leads: 22 AWG, 2-conductor zip-cord
  • Color: White

  • Share your knowledge of this product with other customers... Be the first to write a review

    Browse for more products in the same category as this item:

    Shop Brands > Honeywell Security & Communications > Honeywell Security Sensors > Glassbreak Detector
    Shop Brands > Honeywell Security & Communications > Honeywell Security Sensors
    Burglar Alarms / Intrusion >

    Sensors for Burglar Alarm Systems

    >

    Glass-Break Detectors for Burglar Alarm Systems

    > Ademco
    Burglar Alarms / Intrusion >

    Wireless Products for Burglar Alarm Systems

    >

    Wireless Glass-break Detectors & Shock Sensors for Burglar Alarm Systems


     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please