You are here: Home > Burglar Alarms / Intrusion >

Sensors for Burglar Alarm Systems

>

Glass-Break Detectors for Burglar Alarm Systems

> Ademco
We found 3 results matching your criteria.
Ademco Glass-Break Detectors Magnetic sensors may not detect a break-in if the thief simply smashes a window or a glass door.
Sort By:
Page of 1
Ademco 11-WH - Vibration Contact (White) - 11WH Ademco ASC-SS1 Glassbreak Shock Sensor, 2-wire - ASCSS1
Features:
  • Protects ceilings, walls, safes and glass
  • Adjustable sensitivity
  • Small and inconspicuous
  • White
  • The ASC-SS1 shock sensor protects all types of glass: plate, wired, tempered, and laminated. The sensor will protect the glass within an 8 feet radius from the sensor for glass up to 1/4 inch thick. The ASC-SS1 mounts directly to the glass surface and is wired to a two wire powered protective loop.

    Wiring
    The ASC-SS1 shock sensor is a two wire electronic device which draws minimal current (< 1mA) from the protective loop. When glass is broken, the sensor provides a normally-closed solid-state output (circuit opens on alarm) which is not polarity sensitive. The sensor employs transient suppression devices to protect against lightning.

    The ASC-SS1 shock sensor does not require a processor.

    The ASC-SS1 shock sensor may be wired in series with multiple sensors. Care should be taken to ensure that the total resistance of the sensors in series does not exceed the capabilities of the alarm control panel.

    Testing
    To test the shock sensor, hit the protected glass on the corner furthest from the sensor (see diagram) using a blunt plastic or hard rubber object. This impact should create enough energy for the sensor to generate an alarm condition. Actually breaking the glass would create more energy than the test, so if the test impact causes the sensor to generate an alarm, protection is assured.

    If the unit is tested in the alarm circuit, tripping the detector should trip the alarm panel. An alternate test method is to connect the sensor to an ohm meter and watch the resistance (less than 20Ω when not in alarm) increase to greater than 1MΩ for at least 1 second during an alarm condition.

    Installation
    The ASC-SS1 shock sensor must be mounted in a corner of the glass. For best performance, do not mount the sensor closer than 1" from the window frame.

    Shock sensors mount with double coated acrylic foam tape designed to resist the types of environmental stresses the shock sensor will experience after installation.

    Features:
  • Mounts directly on glass surface
  • Protects all glass types: plate, tempered, laminated and wired
  • Outstanding false alarm immunity
  • Epoxy sealed against moisture and corrosion

    Specifications:
  • Loop Voltage: 3VDC min. to 20 VDC max.
  • Loop Current: 100mA max.
  • Power Requirements: Less than 1mA
  • Transient Suppression: 600 W for 1 mS
  • Alarm Output Type: Normally-closed solid-state output, non-polarized
  • Alarm Output Resistance:
    - 20Ω max. (closed/non-alarm condition)
    - 1MΩ min. (open/alarm condition)
  • Alarm Output Timing: Open for 1 second min. during an alarm condition
  • Operating Temperature: 0oF ~ +130oF (-18oC ~ 55oC)
  • Case Dimensions: 1.4" L x 0.95" W x 0.3" D
  • Wiring Leads: 22 AWG, 2-conductor zip-cord
  • Color: White
  • Ademco / Honeywell 5853 - Wireless Glassbreak Detector

    Honeywell’s 5853 Wireless Glassbreak Detector offers uncompromised performance and unmatched false alarm immunity. The FlexCoreTM signal processor utilizes an Application Specific Integrated Circuit (ASIC) - processing sound data in parallel rather than sequentially. This permits sound frequency, duration and amplitude to be analyzed 50% faster to minimize false alarms while maintaining the highest possible level of detection.

    The 5853 can be mounted on any wall or ceiling within a 25’ range, with no minimum range limitation. The LEDs indicate test mode, alarms and trouble conditions. It is compatible with all 5800 series wireless devices.

    Features:

    • Test mode can be activated remotely with FG-701 Tester
    • Four selectable sensitivity settings (Max, Medium, Low and Lowest)
    • Senses the sound of variety of glass (tampered, wired, laminate, ordinary plate, etc.)
    • FlexCore signal processor
    • Sleek design with front and back case tamper
    • Ten year battery life with easily replaceable batteries

    Specifications:

    • Dimensions : 4.95" H x 3.09" W x 1.1" D
    • Range : : 25' (7.6 meters) maximum from farthest protected glass ; No minimum range
    • Power :
    • Two 3V (Lithium Manganese Dioxide) Batteries (included)
      Replace only with
      - ADEMCO # 466,
      - Panasonic® CR123A,
      - Sanyo® CR123A,
      - Duracell® DL123A, or
      - Varta CR123A
    • Operating Temperature : 14° F – 122° F ( -10° C to 50° C)
       
     
    Ademco Glass-Break Detectors
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please