Home > Shop Brands > Altronix > Access Control >


Altronix Maxim11D - Access Power Controller. Two (2) AL400ULXB. 16 PTC Outputs.

Altronix Maxim11D - Access Power Controller. Two (2) AL400ULXB. 16 PTC Outputs.


Our Price : $449.02

UPC Code: 782239943470

Product Code: 526586




Access Power Controller


This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and/or 24VDC PTC protected outputs. These power outputs can be converted to dry form C contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.


Power Supply/Charger:
12VDC and/or 24VDC output.
Output Power Options:
a) 3.7 amp @ 12VDC plus 3.7 amp @ 12VDC.
b) 2.7 amp @ 24VDC plus 2.7 amp @ 24VDC.
c) 3.7 amp @ 12VDC plus 2.7 amp @ 24VDC.
Class 2 Rated power limited output.
115VAC 60Hz, 2.85 amp input.
Power supply input options:
a) One (1) common power input for either ACM8CB and lock power (factory installed).
b) Two (2) isolated power inputs (external power supply is required). (current is determined by the power supply connected, not to exceed a maximum of 10 amp total).
Input fuse rated @ 3.5 amp.
Filtered and electronically regulated outputs.
Built-in charger for sealed lead acid or gel type batteries.
Maximum charge current .7 amp.
Automatic switch over to stand-by battery when AC fails.
Zero voltage drop when unit switches over to battery backup (AC failure condition).
Short circuit and thermal onerload protection with auto reset.
AC input and DC output LED indicators.
AC fail supervision (form "C" contact).
Battery fail and battery presence supervision (form "C" contact).

Access Power Controller:

Sixteen (16) Access Control System trigger inputs.
Input options:
a) Sixteen (16) normally open (NO) inputs.
b) Sixteen (16) open collector inputs.
c) Any combination of the above.
Sixteen (16) independently controlled PTC protected outputs.
Output options:
a) Sixteen (16) Fail-Safe and/or Fail-Secure power outputs.
b) Sixteen (16) form C 5 amp rated relay outputs.
c) Any combination of the above.
Sixteen (16) auxiliary power outputs (unswitched) (outputs are rated 2.5 amp).
ACM8CB board's main fuse is rated @ 10 amp.
Red LEDs indicate outputs are triggered (relays energized).
Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the Sixteen (16) outputs.
Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC) dry contact input.
b) Polarity reversal input from FACP signaling circuit.
Alarm output relay indicates that FACP input is triggered (form C contact rated @ 1 amp 28VDC not evaluated by UL).
Green LED indicates FACP disconnect is triggered.
Lifetime Warranty.


Accommodates up to four (4) 12VDC/12AH batteries.
Dimensions: 26H x 19W x 6.25D.
1/2" and 3/4" combination knockouts.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Shop Brands > Altronix > Access Control
Shop Brands > Altronix

Enter your email for a chance to WIN $100 Amex Gift Card.

Please Enter Your Email Address

*One entry per household please