Access power controller providing a total of sixteen (16) PTC protected Fail-Safe and/or Fail-Secure power outputs, Fire Alarm disconnect selectable by output. Unit includes one (1) power supply/charger which is 12VDC @ 10 amp and one (1) power supply/charger which is 24VDC @ 10 amp, 115VAC input, AC and battery monitoring. Grey enclosure 26"H X 19"W X 6.25"D. Accommodates up to four (4) 12VDC/12AH batteries.
Overview This unit distributes and switches power to access control systems and accessories. It converts a 115VAC 60Hz input into sixteen (16) independently controlled 12VDC and 24VDC fuse protected outputs. These power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. The unit will route power to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs. Features/Specifications Power Supply/Charger: • 12VDC and 24VDC output. • 9.7 amp @ 12VDC plus 9.7 amp @ 24VDC. • 115VAC 60Hz, 6.3 amp input. • Power supply input options: a) One (1) common power input for either ACM8 and lock power (factory installed). b) Two (2) isolated power inputs (external power supply is required). (current is determined by the power supply connected, not to exceed a maximum of 10 amp total). • Input fuse ratings: - AL1012ULXB input fuse is rated @ 3.5 amp. - AL1024ULXB input fuse is rated @ 10 amp. • Filtered and electronically regulated outputs. • Built-in charger for sealed lead acid or gel type batteries. • Maximum charge current: - AL1012ULXB maximum charge current is .7 amp. - AL1024ULXB maximum charge current is 3.6 amp. • Automatic switch over to stand-by battery when AC fails. • Zero voltage drop when unit switches over to battery backup (AC failure condition). • Short circuit and thermal onerload protection with auto reset. • AC input and DC output LED indicators. • AC fail supervision (form "C" contact). • Battery fail and battery presence supervision (form "C" contact). Access Power Controller: • Sixteen (16) Access Control System trigger inputs. • Input options: a) Sixteen (16) normally open (NO) inputs. b) Sixteen (16) open collector inputs. c) Any combination of the above. • Sixteen (16) independently controlled fuse protected outputs. • Output options: a) Sixteen (16) Fail-Safe and/or Fail-Secure power outputs. b) Sixteen (16) form “C” 5 amp rated relay outputs. c) Any combination of the above. • Sixteen (16) auxiliary power outputs (unswitched) (outputs are rated 3.5 amp). • ACM8CB board's main fuse is rated @ 10 amp. • Red LEDs indicate outputs are triggered (relays energized). • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the Sixteen (16) outputs. • Fire Alarm disconnect input options: a) Normally open (NO) or normally closed (NC) dry contact input. b) Polarity reversal input from FACP signaling circuit. • Alarm output relay indicates that FACP input is triggered (form “C” contact rated @ 1 amp 28VDC not evaluated by UL). • Green LED indicates FACP disconnect is triggered. • Lifetime Warranty. Enclosure • Accommodates up to four (4) 12VDC/12AH batteries. • Dimensions: 26"H x 19"W x 6.25"D. • 1/2 and 3/4 combination knockouts.
Enter your email for a chance to WIN $100 Amex Gift Card.
Please Enter Your Email Address
*One entry per household please