You are here: Home > Audio / Video > Amplifiers
We found 61 results matching your criteria.
Amplifiers
Sort By:
Page of 6
Audiosource AMP100 2-Channel Source Switching Power Amplifier, 50W Audiosource AMP200 2-Channel Source Switching Power Amplifier 80W
Features
  • 50 watts RMS per channel power amplifier with complete custom installer feature set
  • Bridgeable outputs for 150 watts RMS total output power
  • 2 stereo inputs with automatic priority override, and one auxiliary output
  • A, B, or A+B Speaker Selector Switches
  • Front-panel mounted Volume and Balance knobs
  • Manual or Signal-Sensing Power-On
  • 5-way speaker wire binding posts for bare wire or Banana plugs

    Specifications
  • 50 watts RMS per channel into 8 ohm loads with .02% THD+N
  • 60 watts RMS per channel into 4 ohm loads with .02% THD+N
  • Maximum 8 ohm stereo output power at 1% THD+N: 60W
  • Maximum 4 ohm stereo output power at 1% THD+N: 75W
  • Maximum 8 ohm Bridged-Mono output at 1% THD+N: 160W
  • Input needed to reach full output: 1.4v
  • Frequency Response: (20Hz-20kHz)+1dB, -0.5dB; (5Hz-65kHz)+/-3dB
  • Signal to Noise Ratio: 107dB (A-Weighted)
  • Dimensions: 2.9"H x 16.5"W x 9.25"D
  • Weight: 9.6 lbs
  • Power Consumption: 500W
  • Features
  • 80 watts RMS per channel power amplifier with complete custom installer feature set
  • Bridgeable outputs for 250 watts RMS total output power
  • Toroidal Power Supply
  • 2 stereo low-level (RCA) inputs and one high-level (speaker) input, and one auxiliary low-level output
  • Automatic source switching with adjustable delay timer (3-15 seconds)
  • Two sets of speaker outputs selectable from the front panel
  • Rear mounted L/R main volume controls with front mounted volume and balance trim controls
  • Flexible Power-on: Switched, Signal Sensing, and 12v trigger
  • 5-way speaker wire binding posts for bare wire or Banana plugs

    Specifications
  • 80W per CH into 8 ohm loads with less than 0.2% THD+N
  • 125W per CH into 4 ohm loads with less than 0.2% THD+N
  • 250W Bridged Mono into 8 ohms with less than 0.2% THD+N
  • Crosstalk: >65dB @ 1kHz, ref. to rated power into 8 ohms
  • Frequency Response: (20Hz to 20kHz)+0.0dB, -0.5dB
  • Signal to Noise ratio: -103dB ref. to rated power into 4 ohms
  • AC Power Consumption: 700W (all channels driven)
  • Net Weight: 24.3 lbs (11.0 kgs)
  • Gross Weight: 32.2 lbs (14.6.0 kgs)
  • Audiosource AMP51 100W Amplifier Audiosource AMPONEA 80W 2-Channel Power Amplifier
    Audiosource AMP51 100W Amplifier Features
  • All the high-current output you need with none of the features you don't need
  • 80 watts RMS per channel stereo power amplifier with internal bridging
  • Torrodial Power Supply
  • Stable into 2 ohm speaker loads
  • One stereo input and one stereo auxiliary output
  • Rear mounted Stereo/Bridged switch
  • Truely an unbeatable power amplifier for the price
  • 5 way speaker wire binding posts for bare wire or banana plugs

    Specifications
  • 80 watts RMS per channel into 8 ohm loads
  • 100 watts RMS per channel into 4 ohm loads
  • 200 watts RMS bridged into 8 ohm loads
  • Total Harmonic Distortion: <0.04%
  • Intermodulation Distortion: <0.04%
  • Frequency Response: 20Hz-20kHz, +/-0.5dB
  • Signal to Noise Ratio: 110dB
  • Input needed to reach full output: 0.8v
  • Input Impedance: 30kohm
  • Headroom: 2dB
  • Dimensions: 16.5" W x 2.375" H x 11.625" D
  • Weight: 14 lbs, 5 oz
  • Audiosource EQ200 10 Band Graphic Equalizer Audiosource PREAMPRMT Remote Control for Preamplifier Tuner2
  • 10 band stereo graphic equalizer
  • Dual tape monitor loop
  • Multi colored spectrum analyzer display. 6 week lead time
  • LEDs in all sliders
  • Audiosource PREAMPRMT Remote Control for Preamplifier Tuner2
    Crown Audio 1160A 60W 6-Input Commercial Grade Amplifier Crown Audio 1160A Commercial Audio Series 1-Input, 160-Watt, 1-Zone Amplifier
    The Crown 180A, 280A, 1160A and 660A are high-value amplifiers for commercial and industrial audio. They provide 4-ohm and constant-voltage outputs (70V and 100V). The 660A, a six-channel amplifier, provides 4-ohm and constant-voltage outputs (70V and 100V) on channels 1 through 4, and 4-ohm outpus on channels 5 and 6.

    The amps are part of Crown’s Commercial Audio Series, which also includes mixers and mixer-amps. These low-cost units provide all necessary features in a simple building-block format. The sound system can be upgraded as a facility expands. For example, you can add more mixers for more inputs, or add more power amps (or mixer-amps) to handle more zones. Some applications include schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, prisons, and small offices. Typical uses are paging, background music, security and evacuation instructions.

  • 180A has 1 input and one 80W power amplifier for single-zone systems.
  • 280A has 2 inputs and dual 80W power amplifiers for two-zone systems.
  • 1160A has 1 input and one 160W power amplifier for single-zone systems.
  • 660A has six inputs and six 60W power amplifier channels for multi-zone systems. It can drive different types of speakers in different areas of a facility.

    Features

  • 180A, 280A and 1160A have 1 or 2 inputs, 1 or 2 amplifier output channels. 660A has six inputs and six amplifier output channels
  • Ideal for commercial and industrial use
  • Balanced Phoenix-type line inputs; touch-proofed screw-terminal speaker outputs
  • Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications.

    Specifications
  • Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB.
  • Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB.
  • Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD
  • Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.
  • DC Output Offset: < ±5 mV.
  • THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): 800 mV.
  • Input Impedance (nominal): 100 kilohms.
  • Crosstalk (all controls at “10”): –70 dB at 1kHz.
  • Line Output Level (nominal): 1V into 10 kilohms.
  • AC Line Voltages Available:
      100V 50/60 Hz
      120V 60 Hz
      220V 50/60 Hz
      230V 50/60 Hz
      240V 50/60 Hz
  • Operating Temperature/Humidity: 0° C to 40° C at 95% relative humidity (non-condensing).
  • Storage Temperature: –20° C to 85° C.Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB.
  • The Crown 180A, 280A, 1160A and 660A are high-value amplifiers for commercial and industrial audio. They provide 4-ohm and constant-voltage outputs (70V and 100V). The 660A, a six-channel amplifier, provides 4-ohm and constant-voltage outputs (70V and 100V) on channels 1 through 4, and 4-ohm outputs on channels 5 and 6.

    The amps are part of Crown’s Commercial Audio Series, which also includes mixers and mixer-amps. These low-cost units provide all necessary features in a simple building-block format. The sound system can be upgraded as a facility expands. For example, you can add more mixers for more inputs, or add more power amps (or mixer-amps) to handle more zones.

    Some applications include schools, hospitals, factories, restaurant/ retail, houses of worship, fitness facilities, A/V boardrooms, prisons, and small offices. Typical uses are paging, background music, security and evacuation instructions.

    The amplifiers vary in their number of inputs, number of outputs, and power range:

  • 180A has 1 input and one 80W power amplifier for single-zone systems.
  • 280A has 2 inputs and dual 80W power amplifiers for two-zone systems.
  • 1160A has 1 input and one 160W power amplifier for single-zone systems.
  • 660A has six inputs and six 60W power amplifier channels for multi-zone systems. It can drive different types of speakers in different areas of a facility.

    Features
  • 180A, 280A and 1160A have 1 or 2 inputs, 1 or 2 amplifier output channels. 660A has six inputs and six amplifier output channels
  • Ideal for commercial and industrial use
  • Balanced Phoenix-type line inputs; touch-proofed screw-terminal speaker outputs
  • Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

    Specifications
  • Frequency Response (at 1 watt from 4-ohm tap): 70Hz to 19 kHz +/- 1 dB
  • Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB
  • Power Bandwidth (at 4-ohm tap, 2 dB below maximum 1 kHz power): 50 Hz to 20 kHz with < o.5% THD
  • Signal-to-Noise Ration (ref. to rated power, master volume at minimum
  • Crown Audio 1160MA Commercial Audio Mixer/Amplifier, 160W, 4-Inputs, 2-Zone Crown Audio 140MaxPAK 40W XM IX w/ 2 Speakers
    Crown’s Commercial Audio Mixer/Amplifiers deliver legendary Crown quality to the commercial audio industry. These high-value mixer/amplifiers provide both 4-ohm and constant-voltage outputs (70V and 100V) for use in a wide range of commercial applications including schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, prisons, and small offices. Easily configured for a range of uses such as paging, background music, security, and evacuation instructions, Crown’s Commercial Audio units are the smart choice for commercial sound.

      The 180MA has 4 inputs and one 80W power amplifier
      The 1160MA has 4 inputs and one 160W power amplifier
      The 280MA has 8 inputs and dual 80W power amplifiers
    Features
  • 4 to 8 inputs, 1 to 2 amplifier output channels
  • Ideal for commercial and industrial use
  • Expandable by adding Crown Commercial Audio Series mixers or power amplifiers
  • Balanced Phoenix-type mic/line inputs; touch-proof screw-terminal speaker outputs
  • Any input can be sent to any output
  • Built-in four-tone generator
  • Priority muting
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

    Specifications
  • Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz ± 1 dB.
  • Frequency Response (at line out): 20 Hz to 20 kHz ± 1 dB.
  • Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD
  • Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.
  • DC Output Offset: < ±5 mV.
  • THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain):
  • Balanced mic inputs: 3 mV.
  • Balanced line inputs: 800 mV.
  • RCA connectors: 400 mV.
  • Input Impedance (nominal):
      Mic: 400 ohms.
      Line: 100 kilohms.
      RCA: 50 kilohms.
  • Crosstalk: –70dB at 1kHz.
  • Line Output Level (nominal): 1V into 10 kilohms.
  • Phantom Power: 15 VDC.
  • AC Line Voltages Available:
      100V 50/60 Hz
      120V 60 Hz
      220V 50/60 Hz
      230V 50/60 Hz
      240V 50/60 Hz
  • Operating Temperature/Humidy: 0° C to 40° C at 95% relative humidity (non-condensing).
  • Storage Temperature: –20° C to 85° C.
  • Crown Audio 140MaxPAK 40W XM IX w/ 2 Speakers
    Crown Audio 14M 4-Input 1-Zone  Commercial Audio Mixer Crown Audio 180A 80W Commercial Grade Amplifier
    Crowns Commercial Audio Mixers deliver legendary Crown quality to the commercial audio industry. These high-value mixers are designed for use in a wide range of commercial applications including schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, prisons, and small offices. Easily configured for a range of uses such as paging, background music, security, and evacuation instructions, Crowns Commercial Audio units are the smart choice for commercial sound.

    Features
  • The 14M has 4 inputs and 1 output channel
  • The 28M has 8 inputs and 2 output channels
  • Ideal for commercial and industrial use
  • Expandable by adding Crown Commercial Audio Series amplifiers or mixer-amplifiers
  • Balanced Phoenix-type mic/line inputs
  • Any input can be sent to any output channel
  • Built-in four-tone generator
  • Priority muting
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

    Specifications
  • Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB.
  • Signal to Noise Ratio (master volume at minimum): 100 dB.
  • THD: 0.05% typical with 800 mV balanced input, 1V output.
  • Input Sensitivity (volts RMS for full output at maximum gain):
  • Balanced mic inputs: 3 mV.
  • Balanced line inputs: 800 mV.
  • RCA connectors: 400 mV.
  • Input Impedance (nominal): Mic: 400 ohms.
    Line: 100 kilohms.
    RCA: 50 kilohms.
  • Crosstalk (all controls at 10): 50 dB at 1kHz.
  • Line Output Level (nominal): 1.2 V into 10 kilohms.
  • Phantom Power: 15 VDC.
  • AC Line Voltages Available:
      100V 50/60 Hz
      120V 60 Hz
      220V 50/60 Hz
      230V 50/60 Hz
      240V 50/60 Hz
  • Operating Temperature/Humidity: 0 C to 40 C at 95% relative humidity (non-condensing).
  • Storage Temperature: 20 C to 85 C.
  • The Crown 180A, 280A, 1160A and 660A are high-value amplifiers for commercial and industrial audio. They provide 4-ohm and constant-voltage outputs (70V and 100V). The 660A, a six-channel amplifier, provides 4-ohm and constant-voltage outputs (70V and 100V) on channels 1 through 4, and 4-ohm outpus on channels 5 and 6.

    The amps are part of Crown’s Commercial Audio Series, which also includes mixers and mixer-amps. These low-cost units provide all necessary features in a simple building-block format. The sound system can be upgraded as a facility expands. For example, you can add more mixers for more inputs, or add more power amps (or mixer-amps) to handle more zones. Some applications include schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, prisons, and small offices. Typical uses are paging, background music, security and evacuation instructions.

  • 180A has 1 input and one 80W power amplifier for single-zone systems.
  • 280A has 2 inputs and dual 80W power amplifiers for two-zone systems.
  • 1160A has 1 input and one 160W power amplifier for single-zone systems.
  • 660A has six inputs and six 60W power amplifier channels for multi-zone systems. It can drive different types of speakers in different areas of a facility.

    Features

  • 180A, 280A and 1160A have 1 or 2 inputs, 1 or 2 amplifier output channels. 660A has six inputs and six amplifier output channels
  • Ideal for commercial and industrial use
  • Balanced Phoenix-type line inputs; touch-proofed screw-terminal speaker outputs
  • Advanced protection system includes output current limiting, DC protection, circuit breaker/fuse, and thermal protection
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications.

    Specifications
  • Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB.
  • Frequency Response (at line out): 20 Hz to 20 kHz +/- 1 dB.
  • Power Bandwidth (at 4-ohm tap, 2 dB below maxium 1 kHz power): 50 Hz to 20 kHz with < 0.5% THD
  • Signal to Noise Ratio (ref. to rated power, master volume at minimum): 85 dB.
  • DC Output Offset: < ±5 mV.
  • THD: Less than 0.5% at rated power at 1 kHz. Input Sensitivity (for full output at maximum gain): 800 mV.
  • Input Impedance (nominal): 100 kilohms.
  • Crosstalk (all controls at “10”): –70 dB at 1kHz.
  • Line Output Level (nominal): 1V into 10 kilohms.
  • AC Line Voltages Available:
      100V 50/60 Hz
      120V 60 Hz
      220V 50/60 Hz
      230V 50/60 Hz
      240V 50/60 Hz
  • Operating Temperature/Humidity: 0° C to 40° C at 95% relative humidity (non-condensing).
  • Storage Temperature: –20° C to 85° C.Frequency Reponse (at 1 watt from 4-ohm tap): 70 Hz to 19 kHz +/- 1 dB.
  •    
     
    Amplifiers
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please