You are here: Home > Shop Brands > Linear > Wireless Security Solutions > Transmitters > DXS Supervised Transmitters
We found 31 results matching your criteria.
Designates fully supervised models of these same receivers and transmitters. Up to 1,500 feet of range.
Sort By:
Page of 3
Linear A2C/DB25 Serial Port Cable Linear A2C/DB9 Serial Port Cable
Product Number: ACP00417

25-pin for connecting AM/II, AE-1, or AE-2 to a computer's serial port

Product Number: ACP00415

9-pin for connecting AM/II, AE-1, or AE-2 to a computer's serial port

Linear AM-CRI Card Reader Interface - ALSO LISTED AS #  ACP00717 Linear AM-MIO Expansion Interface
Product Number: ACP00717

The AM-CRI card reader interface is designed for use with Linear's access control systems. The interface will support one or two 26-bit or 31-bit Wiegand input devices.

If the readers used have a hold or buffer connection, two readers may be used to the AM-CRI. If the readers do not have a hold or buffer connection, one reader may be used with the AM-CRI.

Usually mounted near the readers, the AM-CRI interface connects to the control unit through a PBUS cable. Each reader connects to the AM-CRI through a six-wire (one LED in reader) or seven wire (two LEDs in reader) cable.
Features

  • For equipping a Linear access control system with one or two Wiegand devices
  • Card Reader Interface can be used with up to two 26 or 31-Bit Wiegand input devices
  • Power is supplied by system controller or external source for locally powered readers
  • 4.45" W x 5.75" H x 1.5" D
  • Product Number: ACP00561

    Input/output expansion interface for the AM-3, AE-1000, & AE-2000, six 5-amp control relays, eight sensing inputs, expandable up to 24 relay outputs and 32 sensing inputs by adding additional AM-RLM modules, plastic cabinet.

    Linear AM-PC Proximity Card - ALSO LISTED AS #ACP00739 Linear AM-PR Proximity Reader
    When ordering, customer must provide the facility code for the reader that these cards will be used with.

    Special Order Item

    Product Number: ACP00739

    Wiegand format proximity type access control card with a slot for attaching to a key ring, use with AM-PR proximity reader.
    Features

  • Passive operation
  • Low-cost
  • Durable
  • Product Number: ACP00740

    The Model AM-PR Proximity Reader is designed for use with Linear's access control systems. This close-range, reader works with either proximity tags or proximity cards. The AM-PR is rugged, rated for extreme weather, and vandal resistant.
    Features

  • Works with both proximity tags and proximity cards
  • Compatible with all Wiegand formats up to 40 bits
  • Weather resistant and vandal resistant
  • 4 to 6 inch read range
  • Supports up to 65,000 cards
  • Easy to install
  • Integral LED confirms when user access is granted
  • 1.6" W x 3.4" H x .6" D
  • Linear AM-RPR Remote Proximity Receiver Linear AM-RRR Remote Radio Receiver
    Product Number: ACP00560

    The Model AM-RPR Remote Proximity Receiver is designed for use with Linear's access control systems. The AM-RPR functions as a remote device that supplies localized radio reception.

    In a typical installation, the AM-RPR would be mounted in a plastic single-gang electrical box next to the controlled opening. When the user requires access, their transmitter must be activated within three inches of the AM-RPR faceplate. The ultra-short range of the AM-RPR allows placement of a unit by each controlled opening without the possibility of the transmitter being detected by the wrong receiver.

    A two-color indicator on the AM-RPR faceplate displays the receiver's status. The indicator lights red when the receiver is getting DC power from the system and turns green when access is granted to a transmitter.

    Features
    • Convenient, cost-effective, and reliable form of door or entrance control
    • 2-to-3-inch radio transmitter read range
    • Compatible with Linear radio-based access control systems
    • 2-color status LED indicates "power on" and "access granted"
    • Installs in a single-gang electrical box
    • Prevents transmitter from being detected by wrong receiver
    • 2.7" W x 4.5" H x 2" D
    Product Number: ACP00500

    The Model AM-RRR Remote Radio Receiver is designed for use with Linear's access control systems. The AM-RRR functions as a remote device that extends the radio range or supplies localized radio reception.

    Three antenna types can be used with this receiver. The cabinet mounted type F connector is for connection to the antenna. The local whip antenna (supplied) screws directly on to the receiver's connector. The directional (EXA-2000) and omni-directional (EXA-1000) remote antennas wire to the receiver's antenna connector with type RG-59 cable.

    An on-board RADIO RANGE knob allows adjustment of the receiver's gain. It can be set to limit the maximum radio range that the receiver can achieve. Two indicators display the receivers performance and operation. The two color red/green STATUS indicator lights red when the receiver is getting DC power and turns green when access is granted to a transmitter. The RADIO indicator lights when the receiver detects a radio signal. It can be used for trouble shooting and verifying system performance. Receiver test points are provided for listening to the incoming signals.

    The receiver is housed in a weather-resistant enclosure and can be mounted indoors or outdoors. Gaskets and a weather-tight wiring strain relief seal the unit from the elements.

    Features

    • Provides extended range for radio-based access control system
    • Up to 500 foot radius radio coverage
    • Weather-resistant housing for outside or indoor mounting
    • Optional directional remote or omnidirectional remote antennas
    • Integral radio gain control for adjustment of radio range
    • 2-color status LEDs indicates "power on" and "access granted"
    • Radio LED detects transmission
    • Power supplied by access controller
    • Low voltage cable allows remote mounting without signal loss
    • RF frequency: 318 MHz
    • 4.25" W x 6.25" H x 2.5" D (without antenna)
    Linear CCM-1 Color Camera for AE-1000 & AE-2000 Linear DXS-10 Supervised Remote Keypad
    Product Number: ACP00904

    Color camera for AE-1000 and AE-2000.
    Features

  • Field upgradeable.
  • Receives power from AE-1000. No need to run additional power.
  • LN-DXS10 / Product Number: SST00079

    The Model DXS-10 Supervised Remote Keypad adds remote control to DVS-1200, DVS-2400 and DUAL-824 Security Systems. The wireless keypad transmitter controls all of the system's modes and can trigger the fire and emergency zones.

    The keypad can be used on a table top or wall mounted and is powered by a 9-volt battery. If the battery becomes low, the keypad will send low battery reports to the system.

    Features

    • Adds remote control to DVS-1200, DVS-2400 and DUAL-824 Security Systems
    • Arming, disarming, fire, and emergency alarm capabilities
    • Telephone style keypad plus system mode keys
    • Wall mounting or tabletop use
    • Powered by one 9-volt battery (included)
    • RF frequency: 315 MHz
    • 3.8" W x 3.56" H x 1.25" D
    Linear DXS-21 Supervised 2-Button, 1-Channel Handheld Transmitter Linear DXS-23 Supervised 3-Button, 4-Channel Handheld Transmitter
    LN-DXS21 / Product Number: SST00094

    The Model DXS-21 Supervised 2-Button, 1-Channel Handheld Transmitter is a supervised, digitally coded radio transmitter designed for use with Linear's DX and DXS Format receivers. Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The top button can be hidden with the top button cover supplied.

    The DXS-21 is a two-button, one-code transmitter. Pressing either the round button on the transmitter's front, or the small button on the transmitter's top will send the same signal.

    The digital DXS code format features over a million possible codes. The DXS transmitters are precoded at the factory to unique codes, so no field coding is required and can send a signal for up to 10 seconds per activation.

    The DXS-21 is supervised for low battery and sends hourly status reports. Some receivers are able to use these signals, others are not. Receivers must be programmed to the transmitter code before system testing and operation. Refer to the receiver's instructions for details on operation and programming.

    Each DXS-21 is powered by two self-contained type 2032 3-volt lithium batteries (included). When the batteries voltage gets low, a low battery report is sent with any alarm or status report to notify the receiver. The red LED will blink when the transmitter is activated with low batteries.

    A removable pocket clip and belt clip are provided for each transmitter. Either can be attached to the back of the transmitter allowing the unit to be clipped to shirt pocket or slid onto a belt.

    Features

    • Complete RF supervision
    • Alarm, supervisory, and low battery transmissions
    • Unique "Extra" top button
    • High visibility operate LED
    • Two type 2032 lithium batteries supplied
    • Pocket and belt clip supplied
    • DXS format
    • RF frequency: 315 MHz
    • 1.6" W x 4.2" H x 0.8" D
    LN-DXS23 / Product Number: SST00095

    The Model DXS-23 Supervised 3-Button, 4-Channel Handheld Transmitter is a supervised, digitally coded radio transmitter designed for use with Linear's DX and DXS Format receivers. Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The top button can be hidden with the top button cover supplied.

    The DXS-23 is a three-button, four-code transmitter. Pressing either of the transmitter's front buttons sends codes one and two. Pressing the small button on the transmitter's top sends code three. Pressing both front buttons together sends code four.

    The digital DXS code format features over a million possible codes. The DXS transmitters are precoded at the factory to unique codes, so no field coding is required and can send a signal for up to 10 seconds per activation.

    The DXS-23 is supervised for low battery and sends hourly status reports. Some receivers are able to use these signals, others are not. Receivers must be programmed to the transmitter code before system testing and operation. Refer to the receiver's instructions for details on operation and programming.

    Each DXS-23 is powered by two self-contained type 2032 3-volt lithium batteries (included). When the batteries voltage gets low, a low battery report is sent with any alarm or status report to notify the receiver. The red LED will blink when the transmitter is activated with low batteries.

    A removable pocket clip and belt clip are provided for each transmitter. Either can be attached to the back of the transmitter allowing the unit to be clipped to shirt pocket or slid onto a belt.

    Features

    • Complete RF supervision
    • Alarm, supervisory, and low battery transmissions
    • Unique "Extra" top button
    • High visibility operate LED
    • Two type 2032 lithium batteries supplied
    • Pocket and belt clip supplied
    • DXS format
    • RF frequency: 315 MHz
    • 1.6" W x 4.2" H x 0.8" D
       
     
    DXS Supervised Transmitters
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please