CPG 20/20-003 - SWIVAL MOUNT FOR FLAME DETECTOR

X3301 Protect?ir Multispectrum Infrared Flame Detector (Spec Sheet: 90-1143, 90-1144,90-1190) establishes the benchmark in multiple-fuel fire detection performance and false alarm
rejection. The detector utilizes advanced signal processing algorithms supported by an embedded 32-bit microprocessor to provide continuous protection in the presence of false
alarm sources and environments with infrared radiation present. The Long Range version has a detection range of 210 feet to a 1 square foot n-Heptane fire and is recommended for any
indoor/outdoor application. The Medium Range version has a detection range of 100 feet to a 1 square foot n-Heptane fire and is recommended for outdoor applications such as offshore
oil/gas platforms where flares or other friendly fires are located. The detector is available in aluminum or 316 stainless steel. Standard outputs include fire alarm, auxiliary alarm, and fault
relays and RS485 Modbus. Optional 4 to 20 mA, Eagle Quantum Premier, or HART output is also available. Pulse output is available for easy retro fitting into controller-based systems.
VENDOR HAS 30% RESTOCK FEE

X3301 Protect?ir Multispectrum Infrared Flame Detector (Spec Sheet: 90-1143, 90-1144,90-1190) establishes the benchmark in multiple-fuel fire detection performance and false alarm
rejection. The detector utilizes advanced signal processing algorithms supported by an embedded 32-bit microprocessor to provide continuous protection in the presence of false
alarm sources and environments with infrared radiation present. The Long Range version has adetection range of 210 feet to a 1 square foot n-Heptane fire and is recommended for any
indoor/outdoor application. The Medium Range version has a detection range of 100 feet to a 1 square foot n-Heptane fire and is recommended for outdoor applications such as offshore
oil/gas platforms where flares or other friendly fires are located. The detector is available in aluminum or 316 stainless steel. Standard outputs include fire alarm, auxiliary alarm, and fault
relays and RS485 Modbus. Optional 4 to 20 mA, Eagle Quantum Premier, or HART output is also available. Pulse output is available for easy retro fitting into controller-based systems.
VENDOR HAS 30% RESTOCK FEE

X2200 UV Flame Detector (Spec Sheet: 90-1157) meets the most stringent requirements worldwide with advanced signal processing and immunity to extraneous sources, combined with
high speed capability. The detector is equipped with both automatic and manual oi test capability. The detector has Division and Zone explosion-proof ratings and is suitable for use in a variety of applications. The standard output configuration includes fire, fault, and auxiliary relays and RS485 Modbus. Optional 4 to 20 mA or Eagle Quantum Premier output also available. A model with pulse output is available for easy retrofitting into existing Det-Tronics controller based systems. A multi-color LED on the detector faceplate indicates detector status condition.
VENDOR HAS 30% RESTOCK FEE

X5200 Ultra VioletIR Flame Detector (Spec Sheet: 90-1156) meets the most stringent requirements worldwide with advanced high speed detection capabilities and immunity to extraneous sources,combined with a superior mechanical design. The combination of Arc rejection on the Ultra Violet sensor and TDSA/Quick on the IR sensor make this detector the highest false alarm immune Ultra Violet IR available. The mounting arrangement allows the Ultra Violet and IR sensors to monitor the same hazardous location with a 90-degree cone of vision. When both sensors simultaneously detect the presence of a flame, an alarm signal is generated. The detector has Division and Zone explosionproof ratings and is suitable for use in indoor and outdoor applications.
VENDOR HAS 30% RESTOCK FEE

X5200 Ultra VioletIR Flame Detector (Spec Sheet: 90-1156) meets the most stringent requirements worldwide with advanced high speed detection capabilities and immunity to extraneous sources,combined with a superior mechanical design. The combination of Arc rejection on the Ultra Violet sensor and TDSA/Quick on the IR sensor make this detector the highest false alarm immune Ultra Violet IR available. The mounting arrangement allows the Ultra Violet and IR sensors to monitor the same hazardous location with a 90-degree cone of vision. When both sensors simultaneously detect the presence of a flame, an alarm signal is generated. The detector has Division and Zone explosionproof ratings and is suitable for use in indoor and outdoor applications.
VENDOR HAS 30% RESTOCK FEE

X5200 Ultra VioletIR Flame Detector (Spec Sheet: 90-1156) meets the most stringent requirements worldwide with advanced high speed detection capabilities and immunity to extraneous sources,combined with a superior mechanical design. The combination of Arc rejection on the Ultra Violet sensor and TDSA/Quick on the IR sensor make this detector the highest false alarm immune Ultra Violet IR available. The mounting arrangement allows the Ultra Violet and IR sensors to monitor the same hazardous location with a 90-degree cone of vision. When both sensors simultaneously detect the presence of a flame, an alarm signal is generated. The detector has Division and Zone explosionproof ratings and is suitable for use in indoor and outdoor applications.
VENDOR HAS 30% RESTOCK FEE

Q1201C Laser Holder is for use with X3301, X3302, X2200, X5200, X9800 and X3300 flame detectors. Easily attaches to the front of Det-Tronics' X-Series flame detectors for use during
system startup, checkout, and re-alignments. Designed to hold the Laser Aimer (which projects a red beam of laser light) to show exact location of the center of the detector's COV. Two additional holding positions are available for locating the outside edges of the COV at either 30 degrees off center (75 degrees total COV) or at 45 degrees off center (90 degrees total COV). While laser is being used to locate edges of the COV it can be rotated 360 degrees to identify the entire area of flame detection coverage.
VENDOR HAS 30% RESTOCK FEE

VENDOR HAS 30% RESTOCK FEE

"The Fenwal Detect-A-Fire Fire Detectors are the ""heart"" of many fire protection systems. These highly reliable devices have been a standard of the industry for over 45 years. Many thousands of these units are now in use controlling the release of extinguishants such as clean agents, CO2, water, or dry chemicals. In some systems the Detect-A-Fire is used as a fire alarm device, to sense overheat or fire and alert personnel. In other systems it is used as a release device, to sense fire and actuate fire attack systems. The Fenwal Detect-A-Fire has met with wide acceptance because it is designed with ""rate compensation."" Rate compensation provides a unique advantage over both fixed temperature and rate-of-rise types of detectors because only the Detect-A-Fire unit accurately senses the surrounding air temperature regardless of the fire growth rate. At precisely the predetermined danger point, the system is activated.
The secret of the unit's sensitivity is in the design. The outer shell is made of a rapidly expanding alloy which closely follows changes in surrounding air temperature. The inner struts are made of a lower expanding alloy. Designed to resist thermal energy absorption and sealed inside the shell, the struts follow temperature changes more slowly. A slow rate fire will heat the shell and struts together. At the ""set point,"" the unit will trigger. A transient rush of warm air up to 40F/min. may expand the shell, but not enough to trigger the unit, virtually eliminating false alarms. If a fast rate fire starts, the shell will expand rapidly. The struts will close and the unit will trigger. The faster the fire rate of growth, the sooner the Detect-A-Fire will react. Fenwal Detect-A-Fire units are not position sensitive. Horizontal and vertical detectors refer to the most common mounting configuration for that unit. Each type can be mounted either horizontally or vertically depending on the application and installation requirements

The Fenwal Detect-A-Fire Fire Detectors are the "heart" of many fire protection systems. These highly reliable devices have been a standard of the industry for over 45 years. Many thousands of these units are now in use controlling the release of extinguishants such as clean agents, CO2, water, or dry chemicals. In some systems the Detect-A-Fire is used as a fire alarm device, to sense overheat or fire and alert personnel. In other systems it is used as a release device, to sense fire and actuate fire attack systems. The Fenwal Detect-A-Fire has met with wide acceptance because it is designed with "rate compensation." Rate compensation provides a unique advantage over both fixed temperature and rate-of-rise types of detectors because only the Detect-A-Fire unit accurately senses the surrounding air temperature regardless of the fire growth rate. At precisely the predetermined danger point, the system is activated.
The secret of the unit's sensitivity is in the design. The outer shell is made of a rapidly expanding alloy which closely follows changes in surrounding air temperature. The inner struts are made of a lower expanding alloy. Designed to resist thermal energy absorption and sealed inside the shell, the struts follow temperature changes more slowly. A slow rate fire will heat the shell and struts together. At the "set point," the unit will trigger. A transient rush of warm air up to 40F/min. may expand the shell, but not enough to trigger the unit, virtually eliminating false alarms. If a fast rate fire starts, the shell will expand rapidly. The struts will close and the unit will trigger. The faster the fire rate of growth, the sooner the Detect-A-Fire will react. Fenwal Detect-A-Fire units are not position sensitive. Horizontal and vertical detectors refer to the most common mounting configuration for that unit. Each type can be mounted either horizontally or vertically depending on the application and installation requirements.