You are here: Home > CCTV / Surveillance > Housings & Mounts > Videolarm > Housings
We found 64 results matching your criteria.
Housings
Sort By:
Page of 6
Videolarm VL-ACE20C Surface Wedge Housing Off White Videolarm VL-ACE20T Indoor Surface Mount Wedge Housing Fixed Camera Bracket Tinted
Videolarm VL-ACE20C Surface Wedge Housing Off White


The smooth curves of the low-profile ACE20 makes it a very attractive surface mount unit. Made of high-impact polycarbonate; it offers sturdiness. Molded-in hinges allows for total access to the camera from below. Hence installation is a snap and servicing simple. Tamper-resistant fasteners are included to protect the camera equipment from vandals. The camera bracket is fully adjustable, and allows the camera to be either top or bottom mounted. The housing cover shall be attached to the base plate, and secured with two tamper-resistant fasteners.

Videolarm VL-ACE20T Indoor Surface Mount Wedge Housing Fixed Camera Bracket Tinted


The smooth curves of the low-profile ACE20 makes it a very attractive surface mount unit. Made of high-impact polycarbonate; it offers sturdiness. Molded-in hinges allows for total access to the camera from below. Hence installation is a snap and servicing simple. Tamper-resistant fasteners are included to protect the camera equipment from vandals. The camera bracket is fully adjustable, and allows the camera to be either top or bottom mounted. The body of the ACE20T housing shall be constructed from high-impact off-white polycarbonate, and shall contain a clear polycarbonate viewing window. The base plate shall be polycarbonate, and shall contain three conduit knockouts on the bottom section for control and video cable. The housing cover shall be attached to the base plate, and secured with two tamper-resistant fasteners.

Videolarm VL-ACEM20CT Indoor 14 Guage Steel Housing for a Fixed Camera Videolarm VL-ACEM20CTH ACEM20C with Factory Installed 24VAC Heater/Thermostat
Videolarm VL-ACEM20CT Indoor 14 Guage Steel Housing for a Fixed Camera


The ACEM20CT is designed for surface mount applications. Constructed of 14-gauge steel, this low profile wedge housing is designed for unobtrusive viewing of a hallway or lobby area. The steel mounting plate that holds the outer housing cover is easy to install and service. The ACEM20CT is the perfect housing in applications where a higher level of security is needed. The body of the housing shall be constructed of 14-gauge steel, off- white powder coat, and contain a clear 3/16" polycarbonate window. An easy-to-replace Window Guard paint shield shall allow clarity of viewing window to be quickly and economically restored in case of vandalism. The base plate shall be 18-gauge steel, and shall contain three conduit knockouts on the bottom section and a 7/8" hole on the rear of the base plate for control and video cable. The housing cover shall be secured to the base plate with four stainless steel 8 x 32 security screws. An optional 24 vac heater/thermostat is available for protected outdoor applications and for defogging the window.

Videolarm VL-ACEM20CTH ACEM20C with Factory Installed 24VAC Heater/Thermostat


The ACEM20CTH is designed for surface mount applications. Constructed of 14-gauge steel, this low profile wedge housing is designed for unobtrusive viewing of a hallway or lobby area. The steel mounting plate that holds the outer housing cover is easy to install and service. The ACEM20CTH is the perfect housing in applications where a higher level of security is needed. The body of the housing shall be constructed of 14-gauge steel, off- white powder coat, and contain a clear 3/16" polycarbonate window. An easy-to-replace Window Guard paint shield shall allow clarity of viewing window to be quickly and economically restored in case of vandalism. The base plate shall be 18-gauge steel, and shall contain three conduit knockouts on the bottom section and a 7/8" hole on the rear of the base plate for control and video cable. The housing cover shall be secured to the base plate with four stainless steel 8 x 32 security screws. An optional 24 vac heater/thermostat is available for protected outdoor applications and for defogging the window. Videolarm's exclusive Window Guard Paint Shield helps protect housing windows from vandals using spray paint or paintball guns.

Videolarm VL-ACH13HB12 Outdoor Housing 12VDC Input with Heater and Blower Videolarm VL-ACH13HB15 IP Network Ready Outdoor Housing with WM1500 Wall Mount
Videolarm VL-ACH13HB12 Outdoor Housing 12VDC Input with Heater and Blower


The environmental ACH13 is an outdoor housing that can accommodate camera/ lens combinations up to 10.5" long and 3.6" wide. This housing is IP Network Ready, & can be equipped with either a 24vac or 12vdc heater/blower. The finish is a shiny white but end caps are black polycarbonate. Sunshield, tamper-resistant fasteners are also available. The ACH13 environmental housing shall be constructed from two extruded aluminum (.08" wall thickness, white finish) halves and two injection-molded polycarbonate end caps. It is capable of accommodating a camera/ lens combinations up to 10.5" long and 3.6" wide. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal. The rear end cap shall have molded standoffs on the inside surface for easy mounting of the optional blower. The top of the housing shall be hinged from the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the aluminum camera sled. An optional 25 vA heater may be mounted to the inside of the bottom extrusion, directly behind the viewing window, for defogging and deicing. Four vent plugs (2 in front, 2 in rear) will create a positive air flow (front to rear) when the blower is in use. Two watertight strain relief plugs will be located at the rear of the housing for separate coax and power cable entry.

Videolarm VL-ACH13HB15 IP Network Ready Outdoor Housing with WM1500 Wall Mount


The environmental ACH13 is an outdoor housing that can accommodate camera/ lens combinations up to 10.5" long and 3.6" wide. This housing is IP Network Ready, & can be equipped with either a 24vac or 12vdc heater/blower. The finish is a shiny white but end caps are black polycarbonate. Sunshield, tamper-resistant fasteners are also available. The ACH13 environmental housing shall be constructed from two extruded aluminum (.08" wall thickness, white finish) halves and two injection-molded polycarbonate end caps. It is capable of accommodating a camera/ lens combinations up to 10.5" long and 3.6" wide. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal. The rear end cap shall have molded standoffs on the inside surface for easy mounting of the optional blower. The top of the housing shall be hinged from the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the aluminum camera sled. An optional 25 vA heater may be mounted to the inside of the bottom extrusion, directly behind the viewing window, for defogging and deicing. Four vent plugs (2 in front, 2 in rear) will create a positive air flow (front to rear) when the blower is in use. Two watertight strain relief plugs will be located at the rear of the housing for separate coax and power cable entry.

Videolarm VL-ACH13HBN IP Camera Housing and Plastic Mount Videolarm VL-ACH13HBWM 13" Environmental Housing with 24VAC Heater and Blower
Videolarm VL-ACH13HBN IP Camera Housing and Plastic Mount


The environmental ACH13 is an outdoor housing that can accommodate camera/ lens combinations up to 10.5" long and 3.6" wide. This housing is IP Network Ready, & can be equipped with either a 24vac or 12vdc heater/blower. The finish is a shiny white but end caps are black polycarbonate. Sunshield, tamper-resistant fasteners are also available. The ACH13 environmental housing shall be constructed from two extruded aluminum (.08" wall thickness, white finish) halves and two injection-molded polycarbonate end caps. It is capable of accommodating a camera/ lens combinations up to 10.5" long and 3.6" wide. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal. The rear end cap shall have molded standoffs on the inside surface for easy mounting of the optional blower. The top of the housing shall be hinged from the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the aluminum camera sled. An optional 25 vA heater may be mounted to the inside of the bottom extrusion, directly behind the viewing window, for defogging and deicing. Four vent plugs (2 in front, 2 in rear) will create a positive air flow (front to rear) when the blower is in use. Two watertight strain relief plugs will be located at the rear of the housing for separate coax and power cable entry.

Videolarm VL-ACH13HBWM 13" Environmental Housing with 24VAC Heater and Blower


The environmental ACH13 is an outdoor housing that can accommodate camera/ lens combinations up to 10.5" long and 3.6" wide. This housing is IP Network Ready, & can be equipped with either a 24vac or 12vdc heater/blower. The finish is a shiny white but end caps are black polycarbonate. Sunshield, tamper-resistant fasteners are also available. The ACH13 environmental housing shall be constructed from two extruded aluminum (.08" wall thickness, white finish) halves and two injection-molded polycarbonate end caps. It is capable of accommodating a camera/ lens combinations up to 10.5" long and 3.6" wide. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal. The rear end cap shall have molded standoffs on the inside surface for easy mounting of the optional blower. The top of the housing shall be hinged from the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the aluminum camera sled. An optional 25 vA heater may be mounted to the inside of the bottom extrusion, directly behind the viewing window, for defogging and deicing. Four vent plugs (2 in front, 2 in rear) will create a positive air flow (front to rear) when the blower is in use. Two watertight strain relief plugs will be located at the rear of the housing for separate coax and power cable entry.

Videolarm VL-ACH13WM 13" Environmental Housing with Wall/Pole Mount/WM1000 Videolarm VL-ACN90C Compact Corner High-Impact Plastic Housing
Videolarm VL-ACH13WM 13" Environmental Housing with Wall/Pole Mount/WM1000


The environmental ACH13 is an outdoor housing that can accommodate camera/ lens combinations up to 10.5" long and 3.6" wide. This housing is IP Network Ready, & can be equipped with either a 24vac or 12vdc heater/blower. The finish is a shiny white but end caps are black polycarbonate. Sunshield, tamper-resistant fasteners are also available. The ACH13 environmental housing shall be constructed from two extruded aluminum (.08" wall thickness, white finish) halves and two injection-molded polycarbonate end caps. It is capable of accommodating a camera/ lens combinations up to 10.5" long and 3.6" wide. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal. The rear end cap shall have molded standoffs on the inside surface for easy mounting of the optional blower. The top of the housing shall be hinged from the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the aluminum camera sled. An optional 25 vA heater may be mounted to the inside of the bottom extrusion, directly behind the viewing window, for defogging and deicing. Four vent plugs (2 in front, 2 in rear) will create a positive air flow (front to rear) when the blower is in use. Two watertight strain relief plugs will be located at the rear of the housing for separate coax and power cable entry.

Videolarm VL-ACN90C Compact Corner High-Impact Plastic Housing


The low-profile ACN90 is corner mount housing that is appealing to the eye. It is designed for indoor applications but yet is strong. It is injected molded with an off-white polycarbonate plastic. In addition, it features tamper resistant fasteners. The style is ideal for office hallways and conference rooms. It has a maximum camera length of 6". The ACN90 indoor housing shall be constructed of off-white, injection-molded polycarbonate plastic and shall be intended for indoor use only. The ACN90 shall be capable of housing a 6" maximum length camera with tilt angles ranging from 5 - 55. The camera will attach to the camera mount with one 1/4-20 screw and rubber pad. The housing shall come complete with tamper-resistant fasteners and convenient cable access slots.

Videolarm VL-AD8CH2 8" Dustproof Outdoor Tubular Housing with 24VAC Heater Videolarm VL-AMS180CT Vandal Resistant Indoor/14 Gauge Steel Housing
Videolarm VL-AD8CH2 8" Dustproof Outdoor Tubular Housing with 24VAC Heater


The dust-proof AD8 aluminum outdoor housing offers excellent protection for your camera. The AD8 environmental housing is designed to prevent dust from entering the housing and have an effect on the camera lens combination. The AD8 offers a hi-res Day/Night color camera with 23x zoom, auto iris lens as an option. Maximum camera length on this tubular housing is 8". The AD8 environmental, dust free housing shall be constructed from .16" (4mm) thick aluminum. Glass faceplate shall be chemically strengthened.

Videolarm VL-AMS180CT Vandal Resistant Indoor/14 Gauge Steel Housing


These premier indoor heavy-duty housings are constructed from 14-gauge steel. Seams are welded and mounting hardware is fully contained inside to prevent intrusion on the camera. In addition, a high-security barrel lock safeguards the single access point. The AMS180 is for wall or ceiling applications and the AMS90 is for corners. The steel construction provides maximum protection to a solid-state camera and lens combination up to 8"

   
 
Housings
 
 

Enter your email for a chance to WIN $100 Amex Gift Card.

Please Enter Your Email Address

*One entry per household please