Standard access control functions, all control electronics secured, 500 users, buffers transactions, real-time clock, RS232 networkable, infrared output to wireless printer. Order number: 0-295033
- Voltage Requirements:
- Hub Control with Proximity Reader 12VDC
- Hub Control with any other Front End 12 to 24 volts AC or DC (selected by jumper)
- W iring Requirements:
- Maximum Distances with shielded : 18 AWG 20 AWG 22 AW G
- Hub Control to Front End 1000 500 250
- Hub Control to Hub Control 1000 500 250
- Hub Control to Printer or PC 1000 500 250
- Current Draw:
- Hub Control only @12VDC 21 ma typical- 51 ma maximum / @24VDC 24 ma typical- 57 ma maximum
- Relays for Propped Door, Forced Door & Alarm Shunt require an additional 15 ma each.
- Indoor, Weather Resistant, Ruggedized, Weather Proof Keypads, Magnetic Card Reader/Keypad and Touch Reader @12VDC 32 ma typical- 62 ma maximum / @24VDC 34 ma typical- 68 ma maximum
- Magnetic Card Reader @12VDC 34 ma typical- 59 ma maximum / @24VDC 36 ma typical- 70 ma maximum
- Mullion Keypad @12VDC 30 ma typical- 58 ma maximum / @24VDC 32 ma typical- 66 ma maximum
- Proximity Reader @12VDC 75 ma typical- 107 ma maximum
- Outputs:
- RS-232 Ports for Printing and Networking Functions: 1200 baud rate, 8 data bits, 1 stop bit, no parity, min 120 CPS printer
- Infrared (IR) output of transaction buffer to handheld printer
- Main relay: SPDT 5 ampere @24 VDC
- Forced Door, Propped Door, Alarm Shunt Relays: SPDT 1 ampere @24 VDC
- MECHANICAL
- Hub Control dimensions: 2.75 w x 4.50 h x 2.50"d
- Indoor & Weather Resistant Keypad dimensions: 2.75 w x 4.50 h x 1.00"d
- W eather Proof Keypad dimensions: 3.00 w x 4.50 h x 1.55"d
- Ruggedized Keypad dimensions: 3.75 w x 5.25 h x 2.50"d
- Mullion Keypad dimensions: 1.75 w x 6.50 h x 1.00"d
- Proximity Reader dimensions: 2.75 w x 4.50 h x 0.50"d
- Touch Reader dimensions: 2.75 w x 4.50 h x 1.75"d
- Mullion Proximity Reader dimensions: 1.75 w x 5.50 h x 0.75"d
- Magnetic Card Reader dimensions: 1.75 w x 4.50 h x 1.55"d
- Magnetic Card Reader/Keypad dimensions: 4.50 w x 4.50 h x 1.55"d
- Magnetic Card Reader Head life expectancy: 300,000 card swipes
- ENVIRONMENTAL
- Temperature: -20 F to 130 F (-28 C to 54 C)
The Secured Series System by IEI is a two part, single door, access control system. When used with
a locking device, it can control access to that particular door. A one door system would consist of one HUB
control module, and up to two front end readers. The door may require a reader on the inside as well as
the outside of the door (for logging of in and out transactions),but the HUB control module can only control
one door.
The HUB is where all memory is stored, and all outputs originate. The HUB control module reads data
sent to it from the front end, determines if access should be granted or not, and energizes the proper outputs.
All relay outputs are located internal to the HUB controller, as well as communication ports for networking,
an internal clock, a keypad for programming, and memory chips to store user information and
transaction log data.
If you wish, you can run communication wires from HUB to HUB for the purpose of sending data,
ie.,user codes, card or touch chip number information from one stand-alone HUB to the next. This is
referred to as networking. Networking will also allow you to transfer data from any HUB in the system to a
serial printer, for example sending the transaction log information, or the list of code, card or chip numbers.
You can also run a network cable from the HUB designated as “Door #1” to a personal computer. This
will allow the owner to easily manipulate important information from HUB to HUB or simply program in and
out information pertaining to the system from one location, the computer. With a computer networked into
the system the owner can now view the list of people by name when looking at the transaction log, and
also assign time zones and holidays limiting certain users to a timed schedule. The personal computer
makes programming easier than from the HUB keypad. This will also require the IEI Secured Series
Software, Model # PCSFTWR. Up to eight HUB controllers may be networked into the system, or on one
personal computer or serial printer.
The HUB control module comes equipped with an infra-red transmitter mounted just to the left of the
red/green bi-color light. You can see the window that the data is transferred out of just above the numbered
digits on the HUB keypad. IEI’s hand held IR-printer, (model# IR-PRINT) will allow you to retrieve
the transaction log or user list from the front of each HUB. WIRELESS! Using the IR port disables the use
of the system with a personal computer, or serial printer.
|
