 |
 |
 |
|
The new Digital Sentry network video recorder (NVR) is optimized by Pelco to deliver the essential hardware support for the DS NVs video management software (VMS) without the extra cost or risk of integrating hardware and software. Boosted by the 2nd Generation Intel Core i7 processor and 8 GB of RAM, Digital Sentry NVR provides an optimal combination of processing power and reliability to meet the demands of HD video recording and playback operations. The system is powered to support up to 128 combined IP and analog video streams, with up to 64 analog cameras supported via the optional ENC5416 direct-attached encoder. Analog streams are also supported using Pelco and third-party encoders.
The new DS NVR delivers total available throughput of 280 Mbps for recording of analog and IP video streams as well as playback and export through the DS ControlPoint client. When determining the maximum number of cameras and the desired frame rate to host on each system, the number of concurrent client connections, the number of streams likely to be viewed in playback on each client, and the bandwidth required to support the client connections must be taken into consideration.
The DS NVR functions as a stand-alone system or as part of a network of servers, monitored from the DS ControlPoint user interface. The system can be deployed solely as a network video recorder, as a digital video recorder (DVR), or as a hybrid NVR. Two gigabit network ports provide for convenient network architecture planning by allowing one port to be dedicated to IP cameras, while the second nework port is used for client connections. Two DVI-D ports provide a convenient connection for high resolution digital monitors for use with HD cameras.
Specifications:
System:
Processor: 2nd Generation Intel Core i7
Operating System: Windows 7 Ultimate 64-bit SP1
Internal Memory: 8 GB RAM
User Interface: DS ControlPoint
Internal Storage (JBOD or RAID 5*):
-DSSRV: 500 GB, 3 TB, 6 TB, 9 TB, 12 TB, 15 TB, or 18 TB
-DSSRV-DVD: 500 GB, 3 TB, 6 TB, 9 TB, or 12 TB
RAID Level: Internal RAID 5 (requires DS-SRV-RAID controller card for hot-swappable drives)
External Storage: Up to 24 TB JBOD or RAID 5 through DX8100HDDI (requires optional DSSRV-SCSI card)
System Drives:
-DSSRV 6, 3.5-inch hard drive bays
-DSSRV-DVD 4, 3.5-inch hard drive bays
Optical Drive: DVD±RW with DSSRV-DVD
Network:
Interface: 2 Gigabit Ethernet RJ-45 (1000Base-T)
Auxiliary Interfaces USB Ports: 1 front (USB 2.0) 4 rear (2 USB 3.0; 2 USB 2.0)
Connections:
Video Out: 2 DVI-D connectors
Audio Out: 1, 1/8-inch audio jack connector
Front Panel Indiactors/Functions:
Buttons: Power
Indicators:
Unit Status: Green, amber, red
Primary Network: Green, amber, red
Secondary Network: Green, amber, red
Software Status: Green, amber, red (based on diagnostics)
Hard Disk Status: Green, red, off (behind bezel)
Environmental:
Operating Temperature: 10° to 35°C (50° to 95°F)
Storage Temperature: -40° to 65°C(-40° to 149°F)
Operating Humidity: 20% to 80%, noncondensing
Maximum Humidity Gradient: 10% per hour
Operating Altitude: -15 to 3,048 m (-50 to 10,000 ft)
Operating Vibration: 0.25 G at 3 Hz to 200 Hz at a rate of 0.5 octave/minute
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 280 Mbps to support IP and analog video
- Supports up to 128 IP Camera Streams; up to 64 Analog Cameras
- Optimized to Support Pre-Installed DS NVs Software
- Records H.264, MJPEG, and MPEG-4 IP Streams
- Supports Pelco and Third-Party IP Cameras and Network Encoders
- Expandable by Networking an Unlimited Number of Servers and Encoders (Dependent on Available Network Bandwidth)
- Compatible with DS ControlPoint for Simultaneous Monitoring of All DS Series and DX Series Products in a Single Client Interface
- Network Health and Event Monitoring Support Through Simple Network Management Protocol (SNMP) and New Digital Sentry System Information (DSSI) Utility
|
|
|
|
|
|
|
|
|
