Home > Shop Brands > Pelco >

  Pelco PEL-CM6700MXB2X Switcher Controller 16 Inputs 2 Outputs NTSC 120 Volt 50/60 Hz

Pelco PEL-CM6700MXB2X Switcher Controller 16 Inputs 2 Outputs NTSC 120 Volt 50/60 Hz


 

Our Price : $862.11


Product Code: PEL-CM6700MXB2X

Qty:

Description
 
The Pelco CM6700MXB2X Matrix switcher/controller is a very affordable, highly versatile, full-featured cross-point matrix switcher. The CM6700 MXB2 X provides switching and control for 16 video inputs and up to 4 monitor outputs from any one of up to 8 keyboards.

The CM6700-MXB2-X Matrix switching unit is designed to be remotely operated from desktop keyboards or external computer systems. The versatile mounting system allows for a variety of installation options: either in a 19-inch rack (front or rear mount), wall, or shelf mount. This versatility allows the bulk of the video cables to be routed to a convenient area such as a telephone room instead of the operator location.

Straightforward on-screen menus make configuring the CM6700MXB2X simple and easy. (The CM6700 MXB2 X even lets you switch to Spanish-language configuration menus.) The user-enabled character display shows time and date, operation mode, camera number, and a 20-character title for quick, easy identification of the on-screen video. The display characters are white with black outline for viewing under varying lighting conditions.

The display can be located anywhere on the viewing monitor and can be turned on or off. The CM6700-MXB2-X supports two system macros, or salvo sequences, to allow quick call-up of up to four cameras to four monitors simultaneously. Salvo sequences include preset call of suitably equipped (PTZ or dome) receivers.

When an alarm is received, the CM6700MXB2X will switch the camera for that alarm to the selected monitors. If a PTZ function is being performed when an alarm is received, an alarm-pending message will appear. An alarm will automatically call a preset and preposition a camera with suitable (PTZ or dome) receivers.

Alarms are cleared either by keyboard acknowledgment or timeout after contact deactivation. Two extra alarm inputs allow for alarm-activated salvo sequence call-up. A Form C alarm relay output allows for automatic activation of an alarm event recorder or other device. In addition, this relay is manually controllable from the system keyboard.

Specifications:

General:

Memory Protection: Replaceable lithium battery provides data protection for ten years
Keyboards: Eight
Receiver/Dome: Control Coaxitron and RS-422
Alarm Inputs: Eighteen, programmable (includes presets and NO/NC device)
Alarm Relay Outputs: One, DPST
Rating: 0.5 amp @ 125 VAC
General Purpose Outputs: Two, open collector; 32 VDC max., 25 mA max.
Data Ports: Two
-Receiver: RS-422, D protocol 2400 baud, P protocol 2400-9600 baud
-Data (Computer): RS-232/RS-422/RS-485, 1200-19.2K baud
Keyboard Ports: Two
-Local Port: Provides data and 12 VAC power for one keyboard
-Remote Port Data only port for all additional or remote keyboards. Each keyboard connected to this port requires a KBDKIT

Electrical:

Power Source: 120V or 230V, 50/60 Hz
Power Consumption: 10W

Switcher Characterstics:

Video Inputs: Sixteen inputs, BNC, terminating or looping (jumper selectable) .5 to 2.0 Vp-p composite video
Video Outputs: Two or four outputs, BNC
Switching Type: Cross-point video matrix. RS-170, NTSC, CCIR and PAL compatible
Switching Method: Vertical interval switching
Switching Time: Less than 16 milliseconds (typical)

Video:

Bandwidth: 17 MHz
Frequency Response: Flat to 8 MHz,±1dB to 15 MHz
Signal-to-Noise Ratio: -55 dB (peak-to-peak vs. RMS noise)
Cross Talk: -50 dB typical at 3.58 MHz
Differential Gain: 2% typical
Differential Phase: 0.2°typical
Tilt: 0.5% typical
Gain Unity: (±1dB)
DC Output: Zero volts

Video Cable Distances Minimum cable requirements:

-75 ohms impedance
-All-copper center conductor
-All-copper braided shield with 95% braid coverage

Character Generation:

Character Type: White with black outline
Camera Identification: One line, twenty characters plus camera number
Date/Time: One line
Programmable: On-screen, menu driven
Character Set: 80 ASCII characters

Mecahnical:

Dimensions (switcher only): 3.5" Hx 17" W x 10.5" D (8.89 cm x 43.18 cm x 26.67 cm)
Mounting (switcher only): Factory configured for EIA rack mount (2 RU); rack ears can be removed for wall mount or freestanding applications
Features
  • 16 Video Inputs; 2 or 4 Video Outputs
  • 20-Character Camera Title
  • Time (24-hour or AM/PM formats); Date (4 formats)
  • Alarm Display Call-up from 18 Direct-Connect Alarm Inputs
  • Video Inputs Individually Selectable for Terminating or Looping
  • Coaxitron Compatible
  • Individual Monitor Sequential Switching with Preset Call
  • Compatible with Pelco's RS-422 D or P Protocol
  • Camera Control Selection: Coaxitron or RS-422; Individually Selectable per Camera
  • Control Genex Multiplexers
  • Selectable Data Port - RS-232/RS-422/RS-485
  • Password Protected Menu Programming
  • User Partitioning to Prevent Unauthorized Viewing

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Shop Brands > Pelco
 
 

Enter your email for a chance to WIN $100 Amex Gift Card.

Please Enter Your Email Address

*One entry per household please