Home > Shop Brands > Pelco >

  Pelco PEL-FR106011SSTR Single Mode 1V A D CC 10-Bit Fiber RX ST Connector

Pelco PEL-FR106011SSTR Single Mode 1V A D CC 10-Bit Fiber RX ST Connector


Our Price : $1,508.68

Product Code: PEL-FR106011SSTR


Pelco FR106011SSTR Single Mode 1V A D CC 10Bit Fiber Rx St Connector: The FR106011SSTR fiber transmitter and receiver provide simultaneous transmission of one unidirectional video channel, two bidirectional audio channels, one bidirectional data channel, and one bidirectional contact closure over one optical fiber. The FR106011SSTR transmitter and the FR106011 receiver are available in multimode and single-mode versions. When using single-mode fiber, the FR106011SSTR transmitter and the FR106011 receiver offer an exceptional optical power budget of 24 dB. Audio and data modes of operation are user selectable by means of a rotary switch. The FR106011SSTR transmitter and the FR106011 receiver can be used with balanced or unbalanced audio signals and allow selection of 600-ohm or 47K-ohm input impedance. Data selection offers a choice of RS-232, RS-422, RS-485 (2-wire/4-wire), Manchester, Bi-Phase, or Coaxitron communication. Using patentpending technology, Coaxitron pan/tilt/zoom (PTZ) control data can be transmitted the full distance of the fiber (up to 6 km for multimode fiber and up to 38 km for single-mode fiber). Modular in design, the FR106011SSTR and FR106011 units can be rack mounted or can be used as stand-alone modules. Rack mounting is accomplished using the RK5000 Series rack mount chassis. Standalone modules can be placed on a desktop or can be mounted to a wall.


Number of Channels: 1
Modulation Type Pulse: code modulation, 10-bit resolution
Video Input/Video Output: 1.0 Vp-p, 75 ohms, NTSC, PAL, and SECAM
Bandwidth: 6.5 MHz
Gain: Unity
Differential Gain: <1%
Differential Phase: <0.7
Tilt: <1%
Signal-to-Noise Ratio: >70 dB (CCIR weighted)
Number of Channels: 2
Audio Input/Audio Output: 2.9 Vp-p maximum
Input Impedance: 600 ohms or 47K ohms, switch-selectable
Input/Output Connection: Balanced (600 ohms) or unbalanced (47K ohms)
Bandwidth: 20 kHz
Total Harmonic Distortion: <0.02%
Signal-to-Noise Ratio: >87 dB
Number of Channels: 1
Data Communication: RS-232, RS-422, RS-485 (2-wire/4-wire),Manchester, Bi-Phase, Coaxitron
Maximum Baud Rate: 500 kbps
Number of Channels: 1
Input: Active low
Output: 30 VDC, 1 A Choice of normally open or normally closed
Operating Temperature: -40 to 167F (-40 to 75C)
Input Power Requirements: 12 VDC or 24 VAC, 350 mA
LED Indicators: Power, Video Present, Audio Present,Data Activity, Contact Closure Activation,Optic Fault
Dimensions: 8.75" D x 1.08" W x 4.81" H;(22.23 x 2.74 x 12.22 cm)
Unit Weight: 1.6 lb (0.73 kg)
Shipping Weight: 3 lb (1.36 kg)
Rack Power/Alarm Connectors:4-pin connector
Stand-Alone Power Connectors: 2-pin connector, screw terminal
Video Connectors: BNC
Audio Connectors: 12-pin connector, tension clamps
Data Connectors: 8-pin connector, tension clamps
Contact Closure Connectors: 6-pin connector, tension clamps
Fiber Optic Connectors: ST for multimode fiber; ST or FC for single-mode fiber
  • Accepts Two 8-Bit Digitally Encoded Video Channels over Two Fibers
  • Compatible with FT8301A and FT8301 Fiber Transmitters
  • Multimode Fiber Support for Distances up to 6 km
  • Single-Mode Fiber Support for Distances up to 46 km
  • Exceeds All Requirements for the RS-250C Medium-Haul Transmission Specification
  • Compatible with NTSC, PAL, and SECAM Video Standards
  • Designed to meet NEMA TS 2 and Caltrans Traffic Signal Control Equipment Environmental Standards
  • No Performance Adjustments Required
  • 12 VDC or 24 VAC Power Supply
  • Standalone and Rack-Mountable Modular Design
  • LED Indicators for Monitoring of Signal Status and Operating Power

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Shop Brands > Pelco

Enter your email for a chance to WIN $100 Amex Gift Card.

Please Enter Your Email Address

*One entry per household please