You are here: Home > Burglar Alarms / Intrusion >

Wireless Products for Burglar Alarm Systems

>

Wireless Carbon Monoxide Detectors for Burglar Alarm Systems

We found 28 results matching your criteria.
Home alarms help prevent theft, but Security Store USA lets you avoid another danger that is sometimes fatal. Carbon monoxide detectors can sense this odorless, colorless gas that kills hundreds each year. Upon detection, the unit will activate a strobe, siren, or other type of alarm. Wireless carbon monoxide detectors offer the implementation advantages shared by wireless burglar alarm systems due to simple, clean installation, and convenient battery-based power.
Sort By:
Page of 3
Linear DXS-80 Supervised Carbon Monoxide Detector Transmitter Silent Call CO1004-3 - Carbon Monoxide Transmitter (contact input)
Supervised Carbon Monoxide Detector Transmitter
Model Number: DXS80 Product Number: SST00116

The DXS-80 Supervised Carbon Monoxide Detector Transmitter is a UL listed, single station, carbon monoxide alarm with a built-in supervised transmitter designed to be used with Linear’s wireless DXS Format Security Systems, Personal Emergency Reporting Systems (PERS), and stand-alone receivers. The DXS-80 provides a warning to alert against both the acute and chronic effects of carbon monoxide (CO) poisoning.

When carbon monoxide is detected, the alarm sounds a loud local alarm. The built-in transmitter sends a digitally coded wireless signal to its companion receiver every 20 seconds until the air has cleared and the detector is restored.

The local alarm can be silenced once by pressing the test/reset button. The transmitter will continue to send an alarm signal every 20 seconds. After 7 minutes, the alarm will sound again if there is still an unsafe carbon monoxide concentration level. The reset function can be used only once for each alarm occurrence.

No field coding is required because the DXS-80 is factory set to a unique code; one of over a million possible codes.

The DXS-80 is powered by one 3-volt lithium battery. The battery is supplied and can power the unit for up to the six year life of the detector. If the battery voltage drops below a preset level the alarm will sound a low battery chirp every 45 seconds and a low battery signal will be sent to the receiver.

At about 6 years, the carbon monoxide detector element will reach the end of its serviceable life. The self-supervising detector will signal a permanent trouble condition, indicating time for replacement.

Features

  • Electrochemical type detector
  • Alarm, status, and low battery transmissions
  • One 3-volt lithium battery supplied
  • Two status indicators
  • Built-in 85 dBA sounder
  • UL listed
  • DXS format
  • RF frequency: 315 MHz
  • 5.375" W x 5.375" H x 2" D
  • This Carbon MonoxideTransmitter is designed to be wired into a home or building alarm system, using a dry contact relay, and is operated by 2 AAA batteries.

    When the panel is activated, the transmitter sends a wireless signal to any Silent Call receiver up to 100 feet away.

    *** Should be installed by a licensed alarm company.
    5 year limited warranty
    Silent Call CO1004-4 - Carbon Monoxide Transmitter (voltage input) Ademco / Honeywell 5800CO Wireless Carbon Monoxide Detector with Built-in Wireless Transmitter - Kit of 5

    This Carbon Monoxide transmitter is designed to be wired into a home or building alarm system, by supplying 12-24 volts from the alarm panel.

    When the alarm system is activated, the Carbon Monoxide alarm transmitter sends a signal to any Silent Call receiver up to 100 feet away.

    ***This transmitter should be installed by a licensed alarm company.
    5 year limited warranty
    5800CO Wireless Carbon Monoxide Detector with Built-in Wireless Transmitter

    The 5800CO is a 3V battery powered wireless carbon monoxide (CO) detector intended for use with Honeywell alarm systems that support 5800 Series wireless devices. It provides early warning when its electrochemical sensing technology measures carbon monoxide levels in the air.

    The 5800CO is specifically designed for system operation and is fully listed to UL 2075 as a system supervised detector.* It contains a piezoelectric horn which generates the ANSI S3.41 temporal 4 pattern in an alarm condition.

    The detector consists of an electrochemical carbon monoxide sensor assembly coupled with a wireless transmitter. The transmitter can send alarm, trouble, end-of-life, tamper and low battery condition messages to the alarm panel.

    Since there are no holes to drill or wires to run, you can preserve the beauty of the home or building while protecting its occupants from harmful carbon monoxide gas. The 5800CO is an ideal carbon monoxide detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

    What is Carbon Monoxide and How Can it Harm Consumers?
    Carbon monoxide (CO) is an odorless, colorless, tasteless and highly toxic gas that is produced when fuels such as wood, gasoline, charcoal and oil are burned with insufficient air. The majority of residential and commercial fatalities caused from these fuels come from heating systems, engine powered tools and charcoal grills. Carbon monoxide is harmful when inhaled because it displaces oxygen in the blood and deprives the heart, brain and other vital organs of oxygen. Large amounts of CO can overcome a person in minutes without warning—causing them to lose consciousness and suffocate.

    The 5800CO is designed to warn the end-user well before the CO reaches a fatal level. The detector’s CO sensitivity is evaluated to UL 2034.

    *For a complete list of products that support system operation of the 5800CO to UL standard 2075, please visit:
    www.security.honeywell.com/hsc/resources/agency/co

    Key Features

    Electrochemical Sensing Technology - Electrochemical detectors are the newest, most refined CO detectors available and provide the most accurate measurement of CO concentration obtainable. They can take readings from low levels that may be hazardous over long periods of time to high concentrations that present an immediate danger.

    Local Sounder - A built-in piezoelectric horn generates the ANSI S3.41 temporal 4 pattern in an alarm condition. The local sounder will also alert the end-user of other conditions such as low battery, detector trouble and end-of-life.

    LED Status Indicators - Dual LEDs provide local visual indication of the detector’s status–including normal operation, alarm, low battery, trouble and end-of-life (see figure 1).

    End of Life Timer - When the detector has reached the end of its life, the detector will send a trouble signal to the panel. This indicates that the CO sensor inside the detector has passed the end of its life and the detector needs to be replaced. The detector’s lifespan is approximately six years from the date of manufacture.

    Full Supervision - The 5800CO is fully supervised to monitor for low battery, case tamper and trouble conditions.

    Test/Hush Button - This dual purpose button allows the end-user to perform periodic testing of the detector. In the event of a CO alarm, this button will silence the local sounder alarm for a five minute period. Note: the Hush feature will not operate at levels above 350 ppm (parts per million) carbon monoxide.

    Versatile Mounting - Whether you choose to affix the detector to the ceiling or a wall, mounting is made simple with the enclosed hardware. The mounting base has large mounting ports, which accommodate drywall anchors for easy surface mounting.

    Tamper Protection and Tamper Resistant Element - The detector has a built-in tamper switch that can communicate back to the control panel in the event it is removed from the base. For an added level of security, the detector also includes a tamper resistant element that prevents removal from the base without the use of a tool.

    Ademco / Honeywell 5800CO Wireless Carbon Monoxide Detector with Built-in Wireless Transmitter Linear DX-COKIT: Supervised Carbon Monoxide Detector Transmitter and Receiver Kit
    5800CO Wireless Carbon Monoxide Detector with Built-in Wireless Transmitter

    The 5800CO is a 3V battery powered wireless carbon monoxide (CO) detector intended for use with Honeywell alarm systems that support 5800 Series wireless devices. It provides early warning when its electrochemical sensing technology measures carbon monoxide levels in the air.

    The 5800CO is specifically designed for system operation and is fully listed to UL 2075 as a system supervised detector.* It contains a piezoelectric horn which generates the ANSI S3.41 temporal 4 pattern in an alarm condition.

    The detector consists of an electrochemical carbon monoxide sensor assembly coupled with a wireless transmitter. The transmitter can send alarm, trouble, end-of-life, tamper and low battery condition messages to the alarm panel.

    Since there are no holes to drill or wires to run, you can preserve the beauty of the home or building while protecting its occupants from harmful carbon monoxide gas. The 5800CO is an ideal carbon monoxide detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

    What is Carbon Monoxide and How Can it Harm Consumers?
    Carbon monoxide (CO) is an odorless, colorless, tasteless and highly toxic gas that is produced when fuels such as wood, gasoline, charcoal and oil are burned with insufficient air. The majority of residential and commercial fatalities caused from these fuels come from heating systems, engine powered tools and charcoal grills. Carbon monoxide is harmful when inhaled because it displaces oxygen in the blood and deprives the heart, brain and other vital organs of oxygen. Large amounts of CO can overcome a person in minutes without warning—causing them to lose consciousness and suffocate.

    The 5800CO is designed to warn the end-user well before the CO reaches a fatal level. The detector’s CO sensitivity is evaluated to UL 2034.

    *For a complete list of products that support system operation of the 5800CO to UL standard 2075, please visit:
    www.security.honeywell.com/hsc/resources/agency/co

    Key Features

    Electrochemical Sensing Technology - Electrochemical detectors are the newest, most refined CO detectors available and provide the most accurate measurement of CO concentration obtainable. They can take readings from low levels that may be hazardous over long periods of time to high concentrations that present an immediate danger.

    Local Sounder - A built-in piezoelectric horn generates the ANSI S3.41 temporal 4 pattern in an alarm condition. The local sounder will also alert the end-user of other conditions such as low battery, detector trouble and end-of-life.

    LED Status Indicators - Dual LEDs provide local visual indication of the detector’s status–including normal operation, alarm, low battery, trouble and end-of-life (see figure 1).

    End of Life Timer - When the detector has reached the end of its life, the detector will send a trouble signal to the panel. This indicates that the CO sensor inside the detector has passed the end of its life and the detector needs to be replaced. The detector’s lifespan is approximately six years from the date of manufacture.

    Full Supervision - The 5800CO is fully supervised to monitor for low battery, case tamper and trouble conditions.

    Test/Hush Button - This dual purpose button allows the end-user to perform periodic testing of the detector. In the event of a CO alarm, this button will silence the local sounder alarm for a five minute period. Note: the Hush feature will not operate at levels above 350 ppm (parts per million) carbon monoxide.

    Versatile Mounting - Whether you choose to affix the detector to the ceiling or a wall, mounting is made simple with the enclosed hardware. The mounting base has large mounting ports, which accommodate drywall anchors for easy surface mounting.

    Tamper Protection and Tamper Resistant Element - The detector has a built-in tamper switch that can communicate back to the control panel in the event it is removed from the base. For an added level of security, the detector also includes a tamper resistant element that prevents removal from the base without the use of a tool.

    DX-COKIT: Supervised Carbon Monoxide Detector Transmitter and Receiver Kit
    Includes one DXS-80 carbon monoxide (CO) detector with a built-in wireless transmitter and one DXR-702 two-channel receiver. The DXS-80 is pre-programmed into the DXR-702.

    Supervised Carbon Monoxide Detector Transmitter and Receiver Kit
    Model Number: DXCOKIT Product Number: SSA00020

    The DX-COKIT Supervised Carbon Monoxide Detector Transmitter and Receiver Kit contains a UL listed, single station, DXS-80 carbon monoxide alarm with a built-in supervised transmitter and DXR-702 2-Channel Receiver. The kit is designed to provide wireless CO detection capability for ANY hardwired alarm control panel. The DXS-80 provides a warning to alert against both the acute and chronic effects of carbon monoxide (CO) poisoning. The receiver provides a Form "C" (normally open & normally closed) relay outputs for connection to an alarm control panel.

    When carbon monoxide is detected, the DXS-80 sounds a loud local alarm. The built-in transmitter sends a digitally coded wireless signal to the DXR-702 receiver every 20 seconds until the air has cleared and the detector is restored. The CO alarm will activate the receiver Channel 1 relay.

    No field coding is required because the DXS-80 is already factory programmed into the DXR-702 receiver. The DXR-702 receiver can be powered from a 11-17 VDC or 12-16 VAC power source. A nine-inch wire whip antenna screws into the receiver’s antenna connector. Optionally, a remote antenna (Model EXA-1000) can be connected to the receiver for greater radio range.

    The DXS-80 is powered by one 3-volt lithium battery. The battery is supplied and can power the unit for up to the six year life of the detector. If the battery voltage drops below a preset level the alarm will sound a low battery chirp every 45 seconds and a low battery signal will be sent to the receiver, activating the receiver's Channel 2 relay.

    At about 6 years, the carbon monoxide detector element will reach the end of its serviceable life. The self-supervising detector will signal a permanent trouble condition, indicating time for replacement.

    DXS-80 Detector Features

  • Electrochemical type detector
  • Alarm and low battery transmissions reported by receiver
  • One 3-volt lithium battery supplied
  • Two status indicators
  • Built-in 85 dBA sounder
  • UL listed
  • DXS format
  • RF frequency: 315 MHz
  • 5.375" W x 5.375" H x 2" D

    DXR-702 Receiver Features

  • 32 transmitter capacity
  • RF activity indicator
  • Quick-learn programming
  • Operates on 11-17 VDC or 12-16 VAC power
  • Two channels
  • Transmitter low battery reporting
  • DX format
  • Two form "C" relay outputs
  • One Amp contact rating @ 24 Volts AC/DC
  • Selectable relay activation time
  • Current consumption: 25 mA standby, 90 mA operating @ 12 VDC
  • RF frequency: 315 MHz
  • 5.5" W x 4.0" H x 1.25" D
  • Locknetics LS4280 US3 Filler Plate 1 1/4 X 3/8 The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

    All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M420 is tested and certified to meet or exceed UL1034 227kg hold force requirements.

    The M420 electromagnetic lock comes in two configurations to meet your specific security needs. The M420 provides basic security, while the M420P, which is our standard option, provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M420P. Kits are available for top jam, double door, and glass door applications.
    The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

    All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M420 is tested and certified to meet or exceed UL1034 227kg hold force requirements.

    The M420 electromagnetic lock comes in two configurations to meet your specific security needs. The M420 provides basic security, while the M420P, which is our standard option, provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M420P. Kits are available for top jam, double door, and glass door applications.
    The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

    All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M420 is tested and certified to meet or exceed UL1034 227kg hold force requirements.

    The M420 electromagnetic lock comes in two configurations to meet your specific security needs. The M420 provides basic security, while the M420P, which is our standard option, provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M420P. Kits are available for top jam, double door, and glass door applications.
    The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

    All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M420 is tested and certified to meet or exceed UL1034 227kg hold force requirements.

    The M420 electromagnetic lock comes in two configurations to meet your specific security needs. The M420 provides basic security, while the M420P, which is our standard option, provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M420P. Kits are available for top jam, double door, and glass door applications.
    The M400 Series line of electromagnetic locks from Schlage are designed with the customer in mind to be robust, easy to install, and secure. The new bayonet mounting feature makes installs easier, allowing the installer to have their hands free during the mounting process. There is no need to consider door handing as all the M400 Series electromagnetic locks are both non-handed and symmetrical, allowing optimum placement of the magnet no matter the application.

    All M400 Series locks have automatic voltage sensing for 12 and 24 volts along with polarity protection to make wiring less complex. The M450 is tested and certified to meet or exceed UL1034 454kg hold force requirements.

    The M450 electromagnetic lock comes in two configurations to meet your specific security needs. The M450 provides basic security, while the M450P, which is our standard option, provides intelligent sensing and reporting features needed to integrate with access control systems. Additional options are available for the M450P. Kits are available for top jam, double door, and glass door applications
       
     
    Wireless Carbon Monoxide Detectors for Burglar Alarm Systems
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please