You are here: Home > Burglar Alarms / Intrusion >

Wireless Products for Burglar Alarm Systems

>

Wireless Glass-break Detectors & Shock Sensors for Burglar Alarm Systems

We found 322 results matching your criteria.
Home alarms can detect possible intruders using glass-break and shock sensors. Security Store USA’s line of glass-break and shock detectors combine the convenience and security of these practical, easy-to-install home alarm sensors with a number of innovations to prevent false alarms. We carry burglar alarm glass-break detectors that use PIR to identify indoor occupants and nullify the alarm, as well as sensors that require both shock and sound for activation. Our home alarm glass-break and shock detectors carry valuable features such as adjustable sensitivity, application to all glass types, and very long battery life.
Sort By:
Page of 27
Ademco ASC-SS1 Glassbreak Shock Sensor, 2-wire - ASCSS1 Bosch DS1101i Glassbreak Detector

The ASC-SS1 shock sensor protects all types of glass: plate, wired, tempered, and laminated. The sensor will protect the glass within an 8 feet radius from the sensor for glass up to 1/4 inch thick. The ASC-SS1 mounts directly to the glass surface and is wired to a two wire powered protective loop.

Wiring
The ASC-SS1 shock sensor is a two wire electronic device which draws minimal current (< 1mA) from the protective loop. When glass is broken, the sensor provides a normally-closed solid-state output (circuit opens on alarm) which is not polarity sensitive. The sensor employs transient suppression devices to protect against lightning.

The ASC-SS1 shock sensor does not require a processor.

The ASC-SS1 shock sensor may be wired in series with multiple sensors. Care should be taken to ensure that the total resistance of the sensors in series does not exceed the capabilities of the alarm control panel.

Testing
To test the shock sensor, hit the protected glass on the corner furthest from the sensor (see diagram) using a blunt plastic or hard rubber object. This impact should create enough energy for the sensor to generate an alarm condition. Actually breaking the glass would create more energy than the test, so if the test impact causes the sensor to generate an alarm, protection is assured.

If the unit is tested in the alarm circuit, tripping the detector should trip the alarm panel. An alternate test method is to connect the sensor to an ohm meter and watch the resistance (less than 20Ω when not in alarm) increase to greater than 1MΩ for at least 1 second during an alarm condition.

Installation
The ASC-SS1 shock sensor must be mounted in a corner of the glass. For best performance, do not mount the sensor closer than 1" from the window frame.

Shock sensors mount with double coated acrylic foam tape designed to resist the types of environmental stresses the shock sensor will experience after installation.

Features:
  • Mounts directly on glass surface
  • Protects all glass types: plate, tempered, laminated and wired
  • Outstanding false alarm immunity
  • Epoxy sealed against moisture and corrosion

    Specifications:
  • Loop Voltage: 3VDC min. to 20 VDC max.
  • Loop Current: 100mA max.
  • Power Requirements: Less than 1mA
  • Transient Suppression: 600 W for 1 mS
  • Alarm Output Type: Normally-closed solid-state output, non-polarized
  • Alarm Output Resistance:
    - 20Ω max. (closed/non-alarm condition)
    - 1MΩ min. (open/alarm condition)
  • Alarm Output Timing: Open for 1 second min. during an alarm condition
  • Operating Temperature: 0oF ~ +130oF (-18oC ~ 55oC)
  • Case Dimensions: 1.4" L x 0.95" W x 0.3" D
  • Wiring Leads: 22 AWG, 2-conductor zip-cord
  • Color: White
  • DS1101i Glassbreak Detector Features a round enclosure.

    The DS1101i Detector uses microprocessor-based Sound Analysis Technology (SAT) to listen for the specific frequencies associated with breaking glass. The DS1101i can be used to detect breakage of plate, tempered, laminated and wired glass types. A built-in environmental test feature alerts the installer of false alarm hazards in harsh environments. A round cover design in available. Glassbreak detectors are intended only as a component of a perimeter protection system. They should always be used in conjunction with motion sensors.

    Features

  • Microprocessor-based Sound Analysis Technology (SAT)
  • Automatic environmental test circuitry
  • Sound check
  • Multiple enclosure designs
  • Bosch DS1102i Glassbreak Detector Bosch DS1103i Glassbreak Detector
    DS1102i Glassbreak Detector Features a square enclosure.

    The DS1101i Detector uses microprocessor-based Sound Analysis Technology (SAT) to listen for the specific frequencies associated with breaking glass. The DS1101i can be used to detect breakage of plate, tempered, laminated and wired glass types. A built-in environmental test feature alerts the installer of false alarm hazards in harsh environments. A round cover design in available. Glassbreak detectors are intended only as a component of a perimeter protection system. They should always be used in conjunction with motion sensors.

    Features

  • Microprocessor-based Sound Analysis Technology (SAT)
  • Automatic environmental test circuitry
  • Sound check
  • Multiple enclosure designs
  • DS1103i Glassbreak Detector Features a rectangle flush mount enclosure.

    The DS1101i Detector uses microprocessor-based Sound Analysis Technology (SAT) to listen for the specific frequencies associated with breaking glass. The DS1101i can be used to detect breakage of plate, tempered, laminated and wired glass types. A built-in environmental test feature alerts the installer of false alarm hazards in harsh environments. A round cover design in available. Glassbreak detectors are intended only as a component of a perimeter protection system. They should always be used in conjunction with motion sensors.

    Features

  • Microprocessor-based Sound Analysis Technology (SAT)
  • Automatic environmental test circuitry
  • Sound check
  • Multiple enclosure designs
  • Bosch DS1110i Series Glassbreak Tester Caddx 2000 Solution 2000 Glassbreak Detector
    DS1110i Series Glassbreak Tester is Used to test DS1100i Series Glass Break Detectors. Powered by a 9 V Alkaline battery (supplied).

    Solution 2000

    The Solution 2000 has a maximum detection range of 25 feet. Its round, low profile design makes it ideal for any surface-mount application, especially ceilings. Status and alarm LEDs are visible through the grille.

    • 3x3 technology
    • Microprocessor based
    • Detects all glass types
    • Power/status LED
    • Alarm memory LED
    • Push button test mode
    • Ceiling or wall mount
    Caddx 2000BP Solution 2000 Glassbreak Detector - Bulk Pack Caddx 2100 Solution 2100 Glassbreak Detector

    Solution 2000

    The Solution 2000 has a maximum detection range of 25 feet. Its round, low profile design makes it ideal for any surface-mount application, especially ceilings. Status and alarm LEDs are visible through the grille.

    • 3x3 technology
    • Microprocessor based
    • Detects all glass types
    • Power/status LED
    • Alarm memory LED
    • Push button test mode
    • Ceiling or wall mount

    The Solution 2100 has a maximum detection range of 20 feet. This detector is designed to recess into a wall or ceiling making it ideal for flush-mount or pre-wire applications. Status and alarm LEDs are visible through the grille.

    Features

  • 3x3 technology
  • Microprocessor based
  • Detects all glass types
  • Power/status LED
  • Detects all glass types
  • Alarm memory LED
  • Push button test mode Ceiling or wall mount

    Specifications

  • Input Voltage: 10-14 Volts AC or DC
  • Current: Alarm Condition 24mA Standby, W/O Status LED 32mA
  • Standby, W/ Status LED 36mA Standby, W/ Latched Alarm and Status LED 38mA
  • Low Voltage: 6.40 Volts (400mV Hysteresis
  • Relay Contacts: 100 VCD, 10 VA, 500 mA
  • Sensitivity: Automatically Adjusted
  • Case Materials: Flame Retardant Injection Molded ABS
  • Operating Temperature: 32°F to 120°F (0°C to 49°C
  • Color: White
  • Caddx 2120 Solution 2120 Glassbreak Detector Caddx 2200 Solution 2200 Glassbreak Detector

    The Solution 2120 is a double-gang version of the 2100. This detector provides a technology upgrade for the replacement of older double-gang sized detectors that have been flush mounted.

    Features

  • 20' range
  • 3x3 technology
  • Microprocessor based
  • Detects all glass types
  • Power/status LED
  • Alarm memory LED
  • Push button test mode
  • Ceiling or wall mount
  • 10-14 Volts AC/DC
  • The Solution 2200 with its timeless styling will complement any decor. This unit has a maximum detection range of 20 feet and will surface mount on either a wall or ceiling.

    Features

  • 20' range
  • 3x3 technology
  • Microprocessor based
  • Detects all glass types
  • Power/status LED
  • Alarm memory LED
  • Push button test mode
  • Ceiling or wall mount

    Specifications

  • Input Voltage: 10-14 Volts AC or DC
  • Current: Alarm Condition 24mA Standby, W/O Status LED 32mA
  • Standby, W/ Status LED 36mA Standby, W/ Latched Alarm and Status LED 38mA
  • Low Voltage: 6.40 Volts (400mV Hysteresis)
  • Relay Contacts: 100 VCD, 10 VA, 500 mA
  • Sensitivity: Automatically Adjusted Case Materials: Flame Retardant
  • Injection Molded ABS
  • Operating Temperature: 32°F to 120°F (0°C to 49°C)
  • Color: White
  • Caddx 5709C-W - ShatterPro handheld glassbreak tester FBII FB-2100 Dual Technology Glassbreak Detector
    The ShatterPro Plus is an acoustic glassbreak sensor combined with a passive infrared motion detector for the purpose of eliminating occupant-generated false alarms. When a person enters the motion detector’s field of view, the glassbreak sensor is shunted for as long as the person remains in the area. The sensor can be wired into a 24-hour perimeter loop, free from concerns about false alarms generated by a noisy environment. It can also function as a combined PIR/glassbreak with individual alarm outputs to the panel for separate zoning. A simple hand clap feature lets the user confirm that the sensor is operational, or a handheld tester can be activated at close range.

    Standard Features


    • 24-hour acoustic glassbreak application
    • Motion-sensitive sensor determines if area is occupied and eliminates residentgenerated false alarms
    • Combines high-quality ShatterPro II analysis with SureShot™ motion signal analysis and detection patterns
    • Two-relay output arms either perimeter, interior loop, or both
  • Unit requires simultaneous shock and sound disturbance to trigger alarm

  • Single detector senses shock and sound waves associated with glass breakage

  • 7,6m range from glass surface

  • Adjustable shock sensitivity

  • Sound sensitivity selection

  • Works with all glass types (Plate, Tempered, Laminated, Wired)

  • SMD construction for better RFI immunity

  • Built-in tamper switch

  • Separate indicator lights for sound, shock and alarm conditions

  • Alarm memory schedule

  •    
     
    Wireless Glass-break Detectors & Shock Sensors for Burglar Alarm Systems
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please