The Model AL-1 Alert Link Nurse Call Pull Cord Interface is a wireless personal alert receiver designed for use with existing nurse call annunciation systems. In a typical installation, the receiver is used in the place of, or in conjunction with, a standard pull cord to activate a corridor light, bed light, room light, and any audible devices to indicate the need for assistance. Up to 32 wireless transmitters can be programmed to activate each receiver.

Three indicators on the front of the receiver display the system status. The green POWER indicator lights when power for the receiver is present. The yellow SERVICE indicator lights if a transmitter has sent a low battery signal. The red ALERT indicator lights when a transmitter has been triggered, showing that the receivers outputs have been activated.

Pressing the RESET button on the top of the receiver for less than two seconds will reset any transmitter low battery indications. Pressing the RESET button for more than three seconds will clear the ALERT indication and reset the relay outputs if in the latched mode.

The receiver contains four normally open 1-amp relay contacts that close when activated. One relay provides an isolated output. The three other relays are isolated when open and have a common return. The receiver relays can operate in normal or failsafe mode. In normal mode, the relays will energize when the receiver is triggered. In failsafe mode, the relays are energized continuously until the receiver is triggered. Failsafe mode supervises the system by causing the outputs to activate if power is removed from the receiver. Both modes provide normally open outputs.

Power for the receiver is supplied by a plug-in transformer. The receiver can be mounted directly to a wall or to a single-gang electrical box with the hardware supplied.

• Interfaces to Most Nurse Call Systems
• Adds Pendant Transmitter Capability
• Emulates a Pull Cord Station
• Fail-Safe Operating Mode
• Trouble Contacts
• Latching or Momentary Outputs
• Accepts up to 32 DX Transmitters
• All Linear DX transmitters are compatible with the Pull Cord ALERTLINK receiver; however, Linear recommends use of the DXT-21, DXT-61A, DXS-62, and the DXS-63
• Includes Power Supply
• RF frequency: 315 MHz
• 3.625" W x 5.25" H x 1.5" D

Features
 

• Two-way voice capability
• Suitable for temporary or permanent installations
• Braille characters for emergency, home, and clear buttons
• Speakerphone capability
• Delayed, silent alarm feature
• Selectable inactivity reporting: 8, 12, or 24 hours
• Selectable two-way voice activation
• Single telephone seizure and true phone line seizure capability
• Distinct alarm tones provided for emergency and fire alarm conditions
• Power on/off switch
• Capacity for up to 16 DX/DXS transmitters
• Point ID communicator reporting
• Programmable with Windows-based RA-2400 Software
• Installs in minutes
• UL listed per standard 1637
• DX and DXS format
• Operating Frequency: 315 MHz
• Backup battery size: 12 volts, 1.2 Amp/hour (not included)
• 7.5" W x 8.75" H x 3" D

The Model PERS-KIT #3 is a system kit with a PERS-2400A Console and several popular accessories for creating a Personal Emergency Reporting System installation.

The system is pre-assembled, tested, and ready to install. The Console has the audio module and battery in place. The transmitter has been programmed into the Console.

The kit includes:

(1) - PERS-2400A Personal Emergency Reporting System Console
(1) - 12VGB 12-volt 1.2 Amp/hour Rechargeable Gel-cell Battery
(1) - VB-4 2-way Audio Module with Voice Prompts
(1) - Telephone cord
(1) - DXS-62 Supervised 1-Button, 1-Channel Pendant/Wristband Transmitter

Features

• Two-way voice capability
• Suitable for temporary or permanent installations
• Braille characters for emergency, home, and clear buttons
• Speakerphone capability
• Delayed, silent alarm feature
• Selectable inactivity reporting: 8, 12, or 24 hours
• Selectable two-way voice activation
• Single telephone seizure and true phone line seizure capability
• Distinct alarm tones provided for emergency and fire alarm conditions
• Power on/off switch
• Capacity for up to 16 DX/DXS transmitters
• Point ID communicator reporting
• Programmable with Windows-based RA-2400 Software
• Installs in minutes
• UL listed per standard 1637
• DX and DXS format
• Operating Frequency: 315 MHz
• Backup battery size: 12 volts, 1.2 Amp/hour (included)
• 7.5" W x 8.75" H x 3" D

The Model PERS-KIT #4 is a system kit with a PERS-3600 Console and several popular accessories for creating a Personal Emergency Reporting System installation.

The system is pre-assembled, tested, and ready to install. The Console has the battery in place. The transmitter has been programmed into the Console.

The kit includes:

(1) - PERS-3600A Personal Emergency Reporting System Console
(1) - 12VGB 12-volt 1.2 Amp/hour Rechargeable Gel-cell Battery
(1) - Telephone cord
(1) - DXS-64 Supervised 1-Button, 1-Channel Waterproof Pendant Transmitter

• Two-way voice capability
• Suitable for temporary or permanent installations
• Braille characters for help, home, and cancel buttons
• Speakerphone capability
• Reminder message capability
• Delayed, silent alarm feature
• Selectable inactivity reporting: 8, 12, or 24 hours
• Selectable two-way voice activation
• Single telephone seizure and true phone line seizure capability
• Distinct alarm tones provided for emergency and fire alarm conditions
• Power on/off switch
• Capacity for up to 16 DX/DXS transmitters
• Point ID communicator reporting
• Programmable with Windows-based RA-2400 Software
• Installs in minutes
• UL listed per standard 1637
• DX and DXS format
• Operating Frequency: 315 MHz
• Backup battery size: 12 volts, 1.2 Amp/hour (30 hour backup)
• 9" W x 5" H x 5-1/2" D

Features

• Two-way voice capability
• Suitable for temporary or permanent installations
• Braille characters for help, home, and cancel buttons
• Speakerphone capability
• Reminder message capability
• Delayed, silent alarm feature
• Selectable inactivity reporting: 8, 12, or 24 hours
• Selectable two-way voice activation
• Single telephone seizure and true phone line seizure capability
• Distinct alarm tones provided for emergency and fire alarm conditions
• Power on/off switch
• Capacity for up to 16 DX/DXS transmitters
• Point ID communicator reporting
• Programmable with Windows-based RA-2400 Software
• Installs in minutes
• UL listed per standard 1637
• DX and DXS format
• Operating Frequency: 315 MHz
• Backup battery size: 12 volts, 1.2 Amp/hour (30 hour backup)
• 9" W x 5" H x 5-1/2" D

The Model PERS-2400A Personal Emergency Reporting System is a supervised wireless emergency reporting product designed for medical alert applications. The table-top or wall-mount Console provides pushbutton emergency assistance to anyone who desires additional security and peace of mind. For the visually impaired, each button on the Console is molded with braille characters to identify the button’s function.

The Console receives signals from up to 16 Linear wireless transmitters. Activating a transmitter causes the Console’s digital communicator to send the appropriate alarm report to the central monitoring station via the standard telephone network. In addition to the central station report, audible and visual indications occur and the alarm relay energizes during an emergency activation.

The emergency alarm can be triggered by the large EMERGENCY button on the face of the Console or with a wireless transmitter. The fire alarm can be triggered by wireless smoke alarms.

Installation and programming are made easy by Linear’s RA-2400 remote access software.

Features

• Two-way voice capability (with optional VB4 voice board)
• Suitable for temporary or permanent installations
• Braille characters for emergency, home, and clear functions
• Speaker phone capability (with optional VB4 voice board)
• Delayed, silent alarm feature
• Selectable inactivity reporting: 8, 12, or 24 hours
• Selectable two-way voice activation (with optional VB4 voice board)
• Single telephone seizure and true phone line seizure capability
• Distinct alarm tones provided for emergency and fire alarm conditions
• Power on/off switch
• Capacity for up to 16 DX/DXS transmitters
• Point ID communicator reporting
• Programmable with Windows-based RA-2400 Software
• Installs in minutes
• UL listed per standard 1637
• DX and DXS format
• Operating Frequency: 315 MHz
• Backup battery size: 12 volts, 1.2 Amp/hour (32 hour backup)
• 7.5" W x 8.75" H x 3" D

The Model PERS-3600 Personal Emergency Reporting System is a supervised wireless emergency reporting product designed for medical alert and panic alert applications. The table-top Console provides assistance to anyone who desires additional security and peace of mind. For the visually impaired, each button on the Console is molded with Braille characters to identify the button’s function.

The console receives signals from up to 16 Linear wireless transmitters. Activating a transmitter causes the Console’s digital communicator to send the appropriate alarm report to the provider’s monitoring station via the standard telephone network. In addition to the monitoring station report, audible and visual indications occur and the alarm relay energizes during an emergency activation. Upon completion of the monitoring station report, two-way voice communications will automatically be initiated between the console and the provider’s operator.

An emergency alarm can be triggered by the large HELP button located on the Console or by a wireless transmitter. A fire alarm can be triggered by optional wireless smoke detectors.

Personal messages can be prerecorded and programmed into the PERS-3600 to remind the client to perform certain functions. “Take your medication”; “call your son” are just two examples of personal messages that can be incorporated into the PERS-3600. Reminder messages can be programmed to play at specific times during the day in daily, weekly, or monthly cycles.

Installation and programming are made easy by Linear’s RA-2400 remote access software.

Features

• UL Listed per UL1637
• Built-in two-way voice capability
• Reminder message capability
• Speakerphone capability
• Multiple subscriber capability - up to sixteen users
• Rechargeable backup battery (30 hour standby capability)
• Inactivity reporting - 8, 12, or 24 hours
• Single telephone line seizure, optional true line seizure capability
• Distinct alarm tones for emergency and fire alarm conditions
• Power on/off switch
• Suitable for permanent or temporary installations
• Installs in minutes
• Electronic Stress Screening assures superior quality

Model Number: RJ-ADAPT

Product Number: AAE00435

The Model RSM-1 Remote Speaker/Microphone a remote speaker-microphone designed for use with Linear’s PERS consoles.

The attractive plastic case houses an 8-ohm speaker and high-sensitivity microphone. The unit is used for 1-way and 2-way voice communications, remotely from the Console. A four-position terminal block is provided for connection to the Console.

The RSM-1 can be tabletop or wall mounted. A wall mounting template is provided on the rear cover of the instruction manual.

• Built-in speaker
• Built-in microphone
• Four-position terminal block
• 5.25" W x 7.5" H x 2" D

Model Number: VB-2

Product Number: AAE00365

Voice board with voice prompts and remote telephone access capabilities. Has two-way voice. Works from a remote touch-tone and from a local touch-tone telephone.

From a remote telephone you can dial, redial, enter PAC code plus #. The console will report system mode, alarms, and trouble. User may change system mode of operation.

From a local telephone you can press # # #, enter PAC code plus #, and the console will report system mode, alarms, and trouble. User may change system mode of operation.

Model Number: VB-4

Product Number: AAE00419