You are here: Home > Shop Brands > Honeywell Security & Communications > Honeywell Wireless Security Products > Smoke Detectors
We found 5 results matching your criteria.
Sort By:
Page of 1
Ademco / Honeywell Wireless Life Safety Combo - 5806W3 and 5800CO Honeywell 5800ZBRIDGE Energy Management Module

Honeywell’s 5806W3 is a 3V battery operated, photoelectronic smoke detector with a built-in wireless transmitter. It facilitates fire verification for false alarm reduction requirements by ANSI/SIA CP-01standards and is intended for use with any of Honeywell’s 5800 Series wireless receiver/transceivers for residential installations. The 5881ENHC or 5883H receivers are required for commercial installations.

The transmitter can send alarm, tamper, maintenance (when control panels are equipped to process maintenance signals) and battery condition messages to the system’s receiver. The maintenance signal fully complies with the sensitivity test requirement specified in NFPA 72, 7-2.2 and is UL approved.

The 5806W3 incorporates a state-of-the-art optical sensing chamber and advanced microprocessor. It also helps eliminate nuisance alarms and virtually eliminates non-billable service calls and fines resulting from false alarms. The microprocessor allows the detector to automatically maintain proper operation at factory calibrated detection levels, even when sensitivity is altered due to the presence of contaminants settling into the unit’s smoke chamber. A removable detector cover and chamber top allows the technician to quickly and easily clean the detector chamber without disassembling the detector head.

Since there are no holes to drill or wires to run, installers can preserve the beauty of the protected premise while protecting it. The 5806W3 is an ideal smoke detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

Features

  • Smoothing Algorithms
    Mathematical calculations in the detector’s software that minimize nuisance alarms by smoothing out short term spikes from dust and smoke.
  • Smart Check
    A signal is sent to the control panel when the detector requires cleaning. This allows a regular, non-emergency service call to clean the detector before it goes into alarm.
  • Drift Compensation
    Virtually eliminates nuisance alarms from long-term dust build-up by automatically adjusting the detector’s sensitivity.
  • Removable Detector Cover and Chamber Top
    Provides the technician the ability to quickly and easily clean the detector chamber without disassembling the detector head.
  • Approved UL Listings for Residential and Commercial Applications
    Both residential and commercial installation requirements are met.
  • Additional LED Status Indicators
    Identifying between alarm or trouble conditions is easier with green and red LED status indicators. The green LED denotes a normal condition while the red LED indicates an abnormal condition.
  • Easy-to-install Mounting Base
    The sturdy mounting base allows the detector to be more easily installed on uneven surfaces (i.e. stucco). The mounting base has larger mounting ports to accommodate drywall anchors for easy surface mounting.
  • Improved Robust RF Field Strength
    The distance between the detector and receiver has been significantly increased.

Additional Features:

  • Utilizes one long-life 3V lithium battery
  • Microcontroller runs on an 4.0 MHz clock
  • Horn operates at 3.3 KHz with sound pressure level of 85dBA at 10 feet
  • Built-in wireless transmitter, temporal code 3 sounder

Specifications:

  • Dimensions : Diameter: 5.3"*, Height: 2.30"
  • Weight : 8.5 oz. (without batteries)
  • Operating Temperature : 32:100°F (0:37.8°C)
  • Humidity Range : 0% to 95% RH, non-condensing
  • Air Velocity : 1,000 ft./min. max.
  • Operating Voltage : 2.5:3.6VDC
  • Standby Current : 8.5 ?A avg.
  • Alarm Current : 35 mA max.
  • Power Source : One 3V CR123A lithium Battery**
  • Audible Output : 85dB min. @ 10 ft.
  • Agency Listings : UL268 : Commercial and Residential


* With adapter bracket (4.9" without mounting base)
**Replacement batteries include Duracell DL123A, Sanyo CR123A, Panasonic CR123A, or ADEMCO 466

The 5800CO is a 3V battery powered wireless carbon monoxide (CO) detector intended for use with Honeywell alarm systems that support 5800 Series wireless devices. It provides early warning when its electrochemical sensing technology measures carbon monoxide levels in the air.

The 5800CO is specifically designed for system operation and is fully listed to UL 2075 as a system supervised detector.* It contains a piezoelectric horn which generates the ANSI S3.41 temporal 4 pattern in an alarm condition.

The detector consists of an electrochemical carbon monoxide sensor assembly coupled with a wireless transmitter. The transmitter can send alarm, trouble, end-of-life, tamper and low battery condition messages to the alarm panel.

Since there are no holes to drill or wires to run, you can preserve the beauty of the home or building while protecting its occupants from harmful carbon monoxide gas. The 5800CO is an ideal carbon monoxide detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

What is Carbon Monoxide and How Can it Harm Consumers? Carbon monoxide (CO) is an odorless, colorless, tasteless and highly toxic gas that is produced when fuels such as wood, gasoline, charcoal and oil are burned with insufficient air. The majority of residential and commercial fatalities caused from these fuels come from heating systems, engine powered tools and charcoal grills. Carbon monoxide is harmful when inhaled because it displaces oxygen in the blood and deprives the heart, brain and other vital organs of oxygen. Large amounts of CO can overcome a person in minutes without warning—causing them to lose consciousness and suffocate.

The 5800CO is designed to warn the end-user well before the CO reaches a fatal level. The detector’s CO sensitivity is evaluated to UL 2034.

With Honeywell's 5800ZBRIDGE module, end-users no longer have to remember to adjust their thermostats or lights when they come and go.

It automatically sets back thermostats and turns lights on or off whenever security systems are armed away or disarmed— saving money and conserving resources every day.

Part of Honeywell’s 5800 Series Wireless family, the easy-to-install 5800ZBRIDGE lets security dealers offer intelligent, cost-effective energy management on every sale.
Compatible with all LYNX and select VISTA (with RF keypad) control panels.
Ademco / Honeywell 5806W3 - Wireless Smoke Detector Ademco / Honeywell 5808W3  - Photoelectric Smoke/Heat Detector with Built-in Wireless Transmitter

Honeywell’s 5806W3 is a 3V battery operated, photoelectronic smoke detector with a built-in wireless transmitter. It facilitates fire verification for false alarm reduction requirements by ANSI/SIA CP-01standards and is intended for use with any of Honeywell’s 5800 Series wireless receiver/transceivers for residential installations. The 5881ENHC or 5883H receivers are required for commercial installations.

The transmitter can send alarm, tamper, maintenance (when control panels are equipped to process maintenance signals) and battery condition messages to the system’s receiver. The maintenance signal fully complies with the sensitivity test requirement specified in NFPA 72, 7-2.2 and is UL approved.

The 5806W3 incorporates a state-of-the-art optical sensing chamber and advanced microprocessor. It also helps eliminate nuisance alarms and virtually eliminates non-billable service calls and fines resulting from false alarms. The microprocessor allows the detector to automatically maintain proper operation at factory calibrated detection levels, even when sensitivity is altered due to the presence of contaminants settling into the unit’s smoke chamber. A removable detector cover and chamber top allows the technician to quickly and easily clean the detector chamber without disassembling the detector head.

Since there are no holes to drill or wires to run, installers can preserve the beauty of the protected premise while protecting it. The 5806W3 is an ideal smoke detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

Features

  • Smoothing Algorithms
    Mathematical calculations in the detector’s software that minimize nuisance alarms by smoothing out short term spikes from dust and smoke.
  • Smart Check
    A signal is sent to the control panel when the detector requires cleaning. This allows a regular, non-emergency service call to clean the detector before it goes into alarm.
  • Drift Compensation
    Virtually eliminates nuisance alarms from long-term dust build-up by automatically adjusting the detector’s sensitivity.
  • Removable Detector Cover and Chamber Top
    Provides the technician the ability to quickly and easily clean the detector chamber without disassembling the detector head.
  • Approved UL Listings for Residential and Commercial Applications
    Both residential and commercial installation requirements are met.
  • Additional LED Status Indicators
    Identifying between alarm or trouble conditions is easier with green and red LED status indicators. The green LED denotes a normal condition while the red LED indicates an abnormal condition.
  • Easy-to-install Mounting Base
    The sturdy mounting base allows the detector to be more easily installed on uneven surfaces (i.e. stucco). The mounting base has larger mounting ports to accommodate drywall anchors for easy surface mounting.
  • Improved Robust RF Field Strength
    The distance between the detector and receiver has been significantly increased.

Additional Features:

  • Utilizes one long-life 3V lithium battery
  • Microcontroller runs on an 4.0 MHz clock
  • Horn operates at 3.3 KHz with sound pressure level of 85dBA at 10 feet
  • Built-in wireless transmitter, temporal code 3 sounder

Specifications:

  • Dimensions : Diameter: 5.3"*, Height: 2.30"
  • Weight : 8.5 oz. (without batteries)
  • Operating Temperature : 32:100°F (0:37.8°C)
  • Humidity Range : 0% to 95% RH, non-condensing
  • Air Velocity : 1,000 ft./min. max.
  • Operating Voltage : 2.5:3.6VDC
  • Standby Current : 8.5 ?A avg.
  • Alarm Current : 35 mA max.
  • Power Source : One 3V CR123A lithium Battery**
  • Audible Output : 85dB min. @ 10 ft.
  • Agency Listings : UL268 : Commercial and Residential


* With adapter bracket (4.9" without mounting base)
**Replacement batteries include Duracell DL123A, Sanyo CR123A, Panasonic CR123A, or ADEMCO 466
Honeywell’s 5808W3 is a 3V lithium powered, photoelectronic smoke/heat detector with a built-in wireless transmitter. It is intended for use with any 5800 Series Wireless Receiver/Transceiver for residential installations (for commercial installations, the 5881ENHC or the 5883H receiver is required).

The transmitter can send alarm, tamper, maintenance (when control panels are equipped to process maintenance signals), and battery condition messages to the system’s receiver. Smoothing algorithms minimize nuisance alarms by smoothing out short term spikes from dust and smoke – virtually eliminating nuisance alarms.

Since there are no holes to drill or wires to run, you can preserve the beauty of the building while protecting it. The 5808W3 is an ideal smoke detector for those difficult to wire locations, applications where room aesthetics are critical, or where hazardous materials exist.

All models also feature a restorable, built-in, fixed temperature (135°F) thermal detector that is also capable of sensing a pre-freeze condition if the temperature is below 41°F.

Features:

  • Improved Robust RF Field Strength
    The distance between the detector and receiver has been significantly increased without the need for a repeater
  • Smoothing Algorithms
    Mathematical calculations in the detector’s software that minimize nuisance alarms by smoothing out short term spikes from dust and smoke
  • Smart Check
    A signal is sent to the control panel when the detector requires cleaning. This allows a regular, non-emergency service call to clean the detector before it goes into alarm.
  • Drift Compensation
    Virtually eliminates nuisance alarms from long-term dust build-up by automatically adjusting the detector’s sensitivity
  • Removable Detector Cover and Chamber Top
    The technician is able to quickly and easily clean the detector chamber without disassembling the detector head
  • Approved UL Listings for Residential and Commercial Applications
    Both residential and commercial installation requirements are met
  • Additional LED Status Indicators
    Identifying between alarm or trouble conditions is a snap with green and red LED status indicators. A green LED denotes a normal condition while the red LED indicates abnormal conditions.
  • Easy-to-install Mounting Base
    The sturdy mounting base allows the detector to be more easily installed on uneven surfaces (i.e. stucco). The mounting base has larger mounting ports, which accommodate drywall anchors for easy surface mounting.

Additional Features:

  • Utilizes one long-life 3V lithium battery
  • Microcontroller runs on a 4.0 MHz clock
  • Horn operates at 3.3 KHz with sound pressure level of 85 dBA at 10 feet
  • Built-in wireless transmitter, temporal code 3 sounder
  • Maintenance signal fully complies with the sensitivity test requirement specified in NFPA 72, 7-2.2 and is approved by UL

Specifications:

  • Dimensions : Diameter: 5.3" *, Height: 2.30"
  • Weight : 8.5 ounces (without batteries)
  • Operating Temperature : 32:100° F (0:37.8° C)
  • Humidity Range : 0% to 95% RH, non-condensing
  • Air Velocity : 1,000 ft./min. max.
  • Operating Voltage : 2.5:3.6VDC
  • Standby Current : 8.5 mA avg.
  • Alarm Current : 35 mA max.
  • Power Source : One 3V CR123A lithium Battery **
  • Audible Output : 85 dB min. at 10 ft.
  • Fixed Temperature Heat Sensor : 135° F Fixed
  • Agency Listings : UL268 - Commercial and Residential


* With adapter bracket (4.9" without mounting base)
**Replacement batteries include Duracell DL123A, Sanyo CR123A, Panasonic CR123A, or ADEMCO 466
Ademco / Honeywell 5809 - Wireless Rate-of-Rise Fixed Temperature Heat Detector

Honeywell’s 5809 wireless fixed heat and rate-of-rise temperature sensor offers expanded fire detection and installation flexibility. It is ideal for hard to wire locations and applications that require more than smoke detection. With no wires to run, the 5809 is fast and easy to install.

The 5809 combines both rate-of-rise and fixed temperature sensors. Fires typically cause a rapid rise in temperature in the surrounding area. The 5809’s rate-of-rise thermostat senses the rise in temperature and signals an alarm if the increase is 15° or more per minute. A built-in fixed temperature sensor will also signal an alarm if the environmental temperature rises above 135°F. The 5809 is UL Listed (UL521) and CSFM approved for commercial and residential applications.

Features

  • Contains a built-in transmitter which can send alarm, supervisory and battery condition messages to the system’s receiver/control unit
  • Powered by a three-volt lithium battery. If the battery voltage gets too low, the 5809 sends a low battery signal to the control panel
  • Features a tamper switch, which causes a trouble signal to be sent to the control if the unit is removed from the mounting base
  • UL Listed for Commercial (when using 5881EH Receiver) or Residential applications

Specifications:

  • Power: 3V lithium battery (Duracell DL123A, Panasonic CR123A, Sanyo CR123A, Varta CR123A)
  • Operating temperature: 40° to 140°F (6° to 60°C)
  • Rate-of-rise temperature: 15°F (8°C) increase per minute (NOTE: Rate-ofrise sensor does not operate above 38°C)
  • Fixed temperature: 135°F (57°C)
  • Maximum spacing: 50 ft x 50 ft UL, 30 ft x 30 ft FM (refer to National Fire Alarm Code Standard NFPA 72 for application requirements)
  • Dimensions: 4.4” diameter/2/2” deep
  • Agency Listings: UL 521 Listed for Commercial (when using 5881EH Receiver) or Residential applications
  • Wireless Transmission Path Test: A good RF transmission path must be established from the proposed mounting location before permanently installing the detector. To determine that there is a good signal reception from the proposed location, perform the test procedure described in the installation instructions procedure.
   
 
 
 

Enter your email for a chance to WIN $100 Amex Gift Card.

Please Enter Your Email Address

*One entry per household please