|
|
|
|
|
|
|
|
|
Using ADEMCO's motion detectors for multiplex system is a smart and sensible thing to do. Whether it's a commercial or residential installation, these newest sensors offer you the following cost-saving benefits: - Point ID identifies the exact location of the intruder. And with the built-in Remote Point Module, the cost is less than a separate module and sensor.
- ADEMCO's patented Global Polling technology senses alarms up to 8 times faster than conventional multiplex.
- ADEMCO's unique 2-wire multiplex reduces installation costs over conventional 4-wire hardwire and multiplex approaches: Wire cost is reduced and less than half the number of connections are necessary - No more need to home run wiring
Each sensor draws super low current, reducing power & battery requirements on large installations while allowing for longer wire runs or smaller gauge wire Features: 35' x 45' coverage Built-in Remote Point Module with DIP switch addressing SMD construction for excellent RFI immunity Spare long range mirror Extremely low current Tamper 6 year over-the-counter warranty
|
It makes sense to use ADEMCO's smart motion detectors for multiplex systems. Not only are they smarter than ever, but they provide the opportunity to reduce your overall installation costs! The 4278EX and 4278EX-SN can be used with any Honeywell alarm system that supports Multiplex Addressing, including the VISTA-40, VISTA-50, 4140XMP, and VISTA-100. The 4278EX may also be used with the 5140XM. Features: Built-in Remote Point Module with Point ID identifies the exact location of the intruder with either a DIP Switch Address (4278EX) or a Serial Number Address as distinctive as a fingerprint (4278EX-SN) Honeywell’s patented Global Polling technology senses alarms up to eight times faster than conventional multiplex Honeywell’s unique two-wire multiplex reduces installation costs over conventional four-wire hardwire and multiplex approaches by reducing both wire costs and the number of connections Super low current, reduces power and battery requirements on large installations Tamper Extra Contact Loop 40ft. x 50ft. Coverage Quad AP Processing for Improved False Alarm Immunity Built-In Remote Point Module Six Year Warranty Specifications: Detection Method: Passive Infrared Coverage:
- wide angle mirror: 40' x 50' (12.2m x 15.2m)
- long range/curtain mirror: 80' x 7.5' (24.4m x 2.3m) Detection Pattern 12 zones - seven main, four intermediate, One downward (wide angle mirror) 1 zone, seven tiers (long range/curtain mirror) Pulse Count: Signal processing/instant response (installer selectable) Detectable Walk Rate 0.5-5 ft/sec (0.15-1.5m/sec) Mounting 7' (2.1m) nominal Indicators: Red LED with enable/disable switch Input Voltage 8-11V peak at polling loop terminals Current Less than 1mA (LED) inactive, 9mA approx. (LED active) Operating Temp: 32° to 122°F (0° to 50°C) Operating Humidity: Up to 95% RH (max.), non-condensing Dimensions: 3 1/4"W x 4 5/8"H x 2"D (85mm x 120mm x 50mm)
|
|
|
|
|
|
|
|
|
|
|
|
|
It makes sense to use ADEMCO's smart motion detectors for multiplex systems. Not only are they smarter than ever, but they provide the opportunity to reduce your overall installation costs! The 4278EX and 4278EX-SN can be used with any Honeywell alarm system that supports Multiplex Addressing, including the VISTA-40, VISTA-50, 4140XMP, and VISTA-100. The 4278EX may also be used with the 5140XM. Features: Built-in Remote Point Module with Point ID identifies the exact location of the intruder with either a DIP Switch Address (4278EX) or a Serial Number Address as distinctive as a fingerprint (4278EX-SN) Honeywell’s patented Global Polling technology senses alarms up to eight times faster than conventional multiplex Honeywell’s unique two-wire multiplex reduces installation costs over conventional four-wire hardwire and multiplex approaches by reducing both wire costs and the number of connections Super low current, reduces power and battery requirements on large installations Tamper Extra Contact Loop 40ft. x 50ft. Coverage Quad AP Processing for Improved False Alarm Immunity Built-In Remote Point Module Six Year Warranty Specifications: Detection Method: Passive Infrared Coverage:
- wide angle mirror: 40' x 50' (12.2m x 15.2m)
- long range/curtain mirror: 80' x 7.5' (24.4m x 2.3m) Detection Pattern 12 zones - seven main, four intermediate, One downward (wide angle mirror) 1 zone, seven tiers (long range/curtain mirror) Pulse Count: Signal processing/instant response (installer selectable) Detectable Walk Rate 0.5-5 ft/sec (0.15-1.5m/sec) Mounting 7' (2.1m) nominal Indicators: Red LED with enable/disable switch Input Voltage 8-11V peak at polling loop terminals Current Less than 1mA (LED) inactive, 9mA approx. (LED active) Operating Temp: 32° to 122°F (0° to 50°C) Operating Humidity: Up to 95% RH (max.), non-condensing Dimensions: 3 1/4"W x 4 5/8"H x 2"D (85mm x 120mm x 50mm)
|
It makes sense to use ADEMCO's 998MX multiplex motion detector. Not only is it smarter than ever, but it provides the opportunity to reduce your overall installation costs! Whether it's a commercial or residential installation, the 998MX offers you the following benefits: Point ID identifies the exact location of the intruder with either a DIP Switch Address or a Serial Number Address as distinctive as a fingerprint. And with the built-in Remote Point Module, the cost is less than a separate module and sensor. ADEMCO's patented Global Polling technology senses alarms up to up to 8 times faster than conventional multiplex. ADEMCO's unique 2-wire multiplex reduces installation costs over conventional 4-wire hardwire and multiplex approaches. Wire cost is reduced and less than half the number of connections are necessary. No more need to home run wiring. Each sensor draws super low current, reducing power & battery requirements on large installations while allowing for longer wire runs or smaller gauge wire. Features: 50' x 50' coverage Built-in Remote Point Module Both DIP switch and serial number addressing EZ-Mount features for fast installation Includes additional long range and pet alley lenses Horizontal and vertical pattern adjustment Automatic temperature compensation Extremely low current Tamper 6 year over-the-counter warranty
|
|
|
|
|
|
|
|
|
|
|
|
|
This bracket fits the Ademco 998 PIR Motion Detector, for swivel mounting
|
Designed to be used with Honeywell control panels that support V-Plex serial number polling loop devices, Honeywell's DT7500SN is a versatile, feature-rich DUAL TEC motion sensor that saves dealers time and money on installations. Automatic walk test saves installers a trip to disable the LED on each unit. Patented K-Band technology is less likely to go through walls and makes set-up and installation simple. Additional benefits include 45° terminal blocks for easy installation, a quicker warm-up time, a panel-initiated walk-test and faster system performance with the Smart Contact mode is critical for video and access control integration.
The DT7500SN is ideal for high security commercial environments where masking and false alarm immunity are a concern, and saves time and money on maintenance when used with Honeywell’s VISTA-FBP panels.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Designed to be used with Honeywell control panels that support V-Plex serial number polling loop devices, Honeywell's IS2500SN is a versatile, feature-rich PIR motion sensor that saves dealers time and money on installations. Automatic walk test saves installers a trip to disable the LED on each unit. Additional benefits include 45° terminal blocks for easy installation, a quicker warm-up time, a panel-initiated walk-test and faster system performance with the Smart Contact mode is critical for video and access control integration.
|
Designed to be used with Honeywell control panels that support V-Plex serial number polling loop devices, Honeywell’s DT7500SN is a versatile, feature-rich DUAL TEC motion sensor that saves dealers time and money on installations. Automatic walk test saves installers a trip to disable the LED on each unit. Patented K-Band technology is less likely to go through walls and makes set-up and installation simple. Additional benefits include 45° terminal blocks for easy installation, a quicker warm-up time, a panel-initiated walk-test and faster system performance with the Smart Contact mode is critical for video and access control integration.
The DT7500SN is ideal for high security commercial environments where masking and false alarm immunity are a concern, and saves time and money on maintenance when used with Honeywell’s VISTA-FBP panels.
|
|
|
