The ASC-SS1 shock sensor protects all types of glass: plate, wired, tempered, and laminated. The sensor will protect the glass within an 8 feet radius from the sensor for glass up to 1/4 inch thick. The ASC-SS1 mounts directly to the glass surface and is wired to a two wire powered protective loop.
WiringThe ASC-SS1 shock sensor is a two wire electronic device which draws minimal current (< 1mA) from the protective loop. When glass is broken, the sensor provides a normally-closed solid-state output (circuit opens on alarm) which is not polarity sensitive. The sensor employs transient suppression devices to protect against lightning.
The ASC-SS1 shock sensor does not require a processor.
The ASC-SS1 shock sensor may be wired in series with multiple sensors. Care should be taken to ensure that the total resistance of the sensors in series does not exceed the capabilities of the alarm control panel.
Testing To test the shock sensor, hit the protected glass on the corner furthest from the sensor (see diagram) using a blunt plastic or hard rubber object. This impact should create enough energy for the sensor to generate an alarm condition. Actually breaking the glass would create more energy than the test, so if the test impact causes the sensor to generate an alarm, protection is assured.
If the unit is tested in the alarm circuit, tripping the detector should trip the alarm panel. An alternate test method is to connect the sensor to an ohm meter and watch the resistance (less than 20Ω when not in alarm) increase to greater than 1MΩ for at least 1 second during an alarm condition.
Installation The ASC-SS1 shock sensor must be mounted in a corner of the glass. For best performance, do not mount the sensor closer than 1" from the window frame.
Shock sensors mount with double coated acrylic foam tape designed to resist the types of environmental stresses the shock sensor will experience after installation.
The 5800SS1 Wireless Shock Sensor mounts directly on glass surfaces. It provides excellent detection for all types of glass while eliminating false alarms and is intended for use with ADEMCO’s 5800 wireless systems only. The 5800SS1 is especially effective in acoustically hard, reverberant rooms like kitchens, bathrooms and laundry rooms that are prone to false alarms.
Since it is a shock sensor, the 5800SS1 is immune to the sounds that cause false alarms. Installation is a snap, just pull the battery tab to enroll the transmitter, peel the adhesive backing and mount. There’s no need to open the case for any reason except to change the battery years later.
Specifications:
Honeywell’s 5853 Wireless Glassbreak Detector offers uncompromised performance and unmatched false alarm immunity. The FlexCoreTM signal processor utilizes an Application Specific Integrated Circuit (ASIC) - processing sound data in parallel rather than sequentially. This permits sound frequency, duration and amplitude to be analyzed 50% faster to minimize false alarms while maintaining the highest possible level of detection.
The 5853 can be mounted on any wall or ceiling within a 25’ range, with no minimum range limitation. The LEDs indicate test mode, alarms and trouble conditions. It is compatible with all 5800 series wireless devices.
Features:
Digital Signal Processing for advanced detection and false alarm immunity. Listens only for the sound of breaking glass from the protected glass zone using patented "Time of Arrival" zone processing and 2 microphones
Ceiling mount design for discreet styling
Detects all types of glass plate, tempered, wired, laminated, coated, sealed insulated
Fast and accurate testing with the FG-701 handheld glassbreak simulator
Flexguard Glassbreak Detection Sets You Apart from the Competition View the video
FG-1625 Glassbreak Detector
The new FG-1625 Glassbreak Detector uses the latest technology to provide faster response and increased false alarm immunity. The FG-1625 is specifically designed to allow fast, easy installation, while the adjustable sensitivity settings can compensate for the acoustics of any room. Optimum operation can be quickly verified using the FG-701 Glassbreak Simulator.
Easy Installation and SetupHoneywell’s patented technology allows remote activation of Test Mode (with simulator). The FG-1625 has a centered wire entry hole, 45° terminal blocks and EOL terminals. A hand-clap feature verifies that the detector is functioning.
Selectable SensitivityTwo DIP switches on the FG-1625 make it easy to set the sensitivity to match the acoustics of the room. Four different sensitivity levels are available, ranging from very low to high. The range can then be verified remotely with the FlexGuard FG-701 Glassbreak Simulator.
Mount the Detector AnywhereMounts on any wall, in the window frame, or on the ceiling, with no minimum range and a maximum range of 25' (7.6m) to the glass.
Covers All Glass TypesThe FG-1625 works on all glass types, including plate, tempered, laminated, wired, film-coated and sealed insulating glass.
Multiple Domain Signal AnalysisThe FG-1625 performs Multiple Domain Signal Analysis in which time, frequency and amplitude characteristics are evaluated for signal qualification. This enables the detector to accurately discriminate false alarms from true glassbreak events.
Enclosed PC BoardThe PCB is protected from potential damage during installation.
Patented Remote Test ModeThe Patented Remote Test Mode can enabled or disable the indicator LEDs using the FG-701 Glassbreak Simulator. The unit automatically resets from Test Mode in five minutes.
Mounting LocationsThe FG-1625 can be mounted on the ceiling, opposite wall, adjoining wall or the same wall as the glass.
The FG1625RFM Glassbreak Detector uses field proven FlexGuard® technology to provide faster response and increased false alarm immunity. The FG1625RFM is specifically designed to allow a fast, easy installation, while the adjustable sensitivity settings can compensate for the acoustics of any room. Optimum operation can be quickly verified using the FG701 Glassbreak Simulator.
The new FG-1625R Glassbreak Detector uses the latest technology to provide faster response and increased false alarm immunity. The FG-1625R is specifically designed to allow fast, easy installation, while the adjustable sensitivity settings can compensate for the acoustics of any room. Optimum operation can be quickly verified using the FG-701 Glassbreak Simulator.
FlexCore Signal Processor The FlexCore Signal Processor is an Application Specific Integrated Circuit (ASIC), which processes sound data in parallel rather than sequentially for faster, more accurate detection decisions. The combination of proven FlexGuard performance with the speed of FlexCore processing provides unmatched false alarm immunity without compromising detection.
Easy Installation and Setup Honeywell’s patented technology allows remote activation of Test Mode (with simulator). The FG-1625R has a centered wire entry hole, 45º terminal blocks and EOL terminals. A hand-clap feature verifies the detector is functioning.
Selectable Sensitivity Two dip switches on the FG-1625 make it easy to set the sensitivity to match the acoustics of room. Four different sensitivity levels are available, ranging from very low to high. The range can then be verified remotely with the FlexGuard FG-701 Glassbreak Simulator.
Mount the Detector Anywhere Mounts on any wall, in the window frame, or on the ceiling, with no minimum range and a maximum range of 25’ (7.6 m) to the glass
Covers All Glass Types The FG-1625 works on all glass types, including plate, tempered, laminated, wired, film-coated, sealed insulating glass.
Multiple Domain Signal Analysis The FG-1625R performs Multiple Domain Signal Analysis in which time, frequency and amplitude characteristics are evaluated for signal qualification. This enables the detector to accurately discriminate false alarms from true glassbreak events.
Enclosed PC Board The PCB is protected from potential damage during installation.
Patented Remote Test Mode The Patented Remote Test Mode can enable or disable the indicator LEDs remotely using the FG-701 Glassbreak Simulator. The detector automatically resets from Test Mode in five minutes.
Mounting Locations The FG-1625R can be mounted on the ceiling, opposite wall, adjoining wall, or the same wall as the glass.
Serial number addressable
New hinged-case styling same as FG-1625
Set-up and performance identical to FG-1625
Glassbreak Simulator
Compatible with all IntelliSense and ADEMCO brand glassbreak detectors
Calibrated signal output to allow true range verification
Remote test-mode activation – works from 15 ft away*
Low battery voice announcement
Digitally produced glassbreak sound
*when used with FG-1525 and FG-1625 series detectors
