The Model ANT-1A 7-inch Mid-range Antenna works with Linear's line of 27 MHz mid-range transmitters and receivers. The Model ANT-1A is an 7-inch rubber duck antenna for short range applications (less than 1 mile). The ANT-1A is supplied with a CON-180A (straight) connector to mate the antenna to a transmitter or receiver. For a right angle antenna mounting, add a CON-90A right angle connector between the ANT-1A antenna and the CON-180A connector.

• Antenna for Linear's mid-range transmitters and receivers
• Seven-inch "rubber duck" style
• Supplied with CON-180A straight antenna connector
• Order CON-90A connector for right angle antenna mounting
• .65" W x 7" H x .65" D

The Model ANT-2 3-foot Mid-range Antenna works with Linear's line of 27 MHz mid-range transmitters and receivers. The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from mid-range units is required

Features

• Antenna for Linear's mid-range transmitters and receivers
• Three-foot whip style
• 18 feet of coax cable included
• "U" bolt included for post mounting
• 2.25" W x 39" H x 2" D

The Model CON-90A Right Angle Antenna Connector works with Linear's line of 27 MHz mid-range transmitters and receivers. The Model ANT-1A mid-range antenna is supplied with a CON-180A (straight) connector to mate the antenna to a transmitter or receiver. For a right angle antenna mounting, add a CON-90A right angle connector between the ANT-1A antenna and the CON-180A connector.

• Connector for Linear's mid-range transmitter and receiver ANT-1A antenna
• Right angle female-to-male type BNC connector
• .57" W x .93" H x 1.14" D

Model Number: CON-180A

Model Number: T-1224DC

Product Number: AAE00381

Model Number: T-124.8DC

Product Number: AAE00382

The Model T-90D Supervised Door/Window Transmitter is a supervised, digitally-coded radio transmitter designed for applications such as door/window security. The T-90D is supervised for alarms and restorals, low battery, status, tamper, and test. The T-90D transmitter is compatible with any Linear SX format supervised security receiver.

Coding switches are not required or used in the T-90. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible.

The T-90D can be triggered with the built-in internal magnetic contacts, with various types of external contacts, or both. When using one of the internal contacts and the external input, both sensors must be secured for a restore transmission, faulting either sensor will cause an alarm transmission. External inputs can be either normally open or normally closed.

Switch selected options are included for glass break sensors, built-in pulse stretcher, battery saver, and external input type.

The transmitter is powered by two self-contained type 2032 3-volt batteries. These batteries are supplied with the transmitter and have sufficient life for most installations. Larger, type 2450 batteries can be used to power the transmitter longer in high traffic installations. When the battery voltage gets low, a low battery report is sent with any status, alarm, tamper or test report to the receiver.

Features

• Compact, attractive style
• Fully supervised
• Tamper switch
• Test switch
• Internal reed switches
• Supplied with adjustable external magnet
• Over 16,000,000 preprogrammed codes
• External contact terminals
• Installer selected external contact mode N/O or N/C
• Fast or slow response glass break sensor selection
• Plastic mounting shoe with tamper Lock
• Powered by 2032 two lithium batteries (included)
• Optional 2450 lithium batteries can be used for extended life
• Linear SX radio format
• RF frequency: 303.875 MHz
• 1.5" W x 3.3" H x 0.88" D

The Model XR-1 1-Channel Mid-range Receiver is designed for use in various wireless remote control applications. When the Model XR-1 receiver detects a signal from its companion transmitter, it will verify the digital code, activate its output, and trigger the remote device connected to the receiver.

The XR-1 receiver has full supervision capabilities. If the status option is selected, the receiver expects hourly status signals from its transmitter. If these signals cease, the receiver will indicate trouble by activating its status output after four hours. Contact supervision allows the receiver's output to follow the transmitter's input, staying activated as long as the transmitter input is activated. Alternately, an auto-restore option can be selected in the transmitter, causing a momentary receiver output each time the transmitter input is activated. If the transmitter sends a low battery signal, the receiver's low battery output will activate.

Power for the XR-1 receiver can come from an external regulated 12 VDC power supply (Linear Model T-1224DC) or from a 12-volt battery. A diode protects the unit from reverse power polarity. The XR-1 draws about 30 mA standby, and about 70 mA when the output is active. The receiver output provides isolated N/O and N/C relay contacts capable of switching a maximum of 1 Amp @ 32 VDC. The low battery and status outputs are solid state and are capable of switching up to 50 mA @ 20 VDC to ground.

Two antennas (sold separately) are available for the XR-1. The Model ANT-1A is an 7-inch rubber duck antenna for short range applications (less than 1 mile). The ANT-1A is supplied with a CON-180A (straight) connector to mate the antenna to the transmitter. For a right angle antenna mounting, use a CON-90A right-angle connector with the CON-180A. The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from the XR-1 is required. A common 9-foot 1/4 wave CB whip antenna can also be used with the XR-1 for maximum range.

Two 8-position switches set the unit's system code. This code must be matched in the XR-1's transmitter. There are 65,536 different system codes possible. The 4-position option switch selects the receiver's channel (to match the transmitters channel), and status supervision option.

The receiver is housed in a rugged weather-resistant metal enclosure with a sturdy SO-239 antenna connector and a water-tight wiring strain relief bushing. Two indicators are visible through a window on the case. The green power indicator lights when the receiver has power. During reception, the red RF indicator lights. Two internal test points are provided for signal strength and audio monitoring.

Features

• Up to 10 Miles of Line-of-Sight Range (with XT-1 and XT-4)
• Up to Two Miles of Line-of-Sight with Handheld Devices
• Superheterodyne Receiver Technology
• Over 64,000 Codes
• Form "C" Alarm Output
• Weather-Resistant Case
• Power On and RF Activity Indicators
• Optional RF Supervision
• RF frequency: 27.255 MHz
• 4.25" W x 6.25" H x 2.5" D

The Model XR-16 16-Channel Mid-range Receiver is designed for use in various wireless remote control applications. When the Model XR-16 receiver detects a signal from its companion transmitters, it will verify the digital code, activate the correct output channel, and trigger the remote device connected to the receiver.

The XR-16 receiver has full supervision capabilities. If the status option for a channel is selected, the receiver expects hourly status signals from that channel's transmitter. If these signals cease, the receiver will indicate trouble by activating its status output after four hours. Contact supervision allows the receiver's outputs to follow the transmitter's inputs, each output staying activated as long as each transmitter input is activated. Alternately, an auto-restore option can be selected in the transmitter, causing a momentary receiver output each time any transmitter input is activated. If the transmitter sends a low battery signal, the receiver's low battery output will activate.

Power for the XR-16 receiver can come from an external 12 VDC power supply (Linear Model T-1224DC) or from a 12-volt battery. A diode protects the unit from reverse power polarity. The XR-16 draws about 50 mA standby, and about 350 mA when all outputs are active. The alarm, low battery and status outputs are solid state and are capable of switching up to 100 mA @ 24 VDC to ground (programmable as N/O or N/C). The receiver's relay can activate with all signals, or just alarm signals. It provides isolated N/O and N/C relay contacts capable of switching a maximum of 1 Amp @ 24VDC.

Two antennas (sold separately) are available for the XR-16. The Model ANT-1A is an 7-inch rubber duck antenna for short range applications (less than 1 mile). The ANT-1 requires a Model CON-180A connector to mate the antenna to the receiver. The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from the XR-16 is required. A common 9-foot 1/4 wave CB whip antenna can also be used with the XR-16 for maximum range.

Two 8-position switches set the unit's system code. This code must be matched in the XR-16's transmitters. There are 65,536 different system codes possible. The two 8-position option switches select the status supervision option for each of the 16 channels.

The receiver is housed in a metal enclosure with an SO-239 antenna connector. Three displays are visible through a window on the case. The left two displays show the channel number, the right display shows the condition. The display scrolls through all the channel numbers with a condition. The right decimal point lights when the receiver has power. During reception, the center decimal point lights. Two internal test points are provided for signal strength and audio monitoring.

Features

• Up to 10 Miles of Line-of-Sight Range (with XT-1 and XT-4)
• Up to Two Miles of Line-of-Sight with Handheld Devices
• Superheterodyne Receiver Technology
• Over 64,000 Codes
• Open Collector Alarm Outputs
• Common relay output
• Power On and RF Activity Indicators
• Optional RF Supervision
• RF frequency: 27.255 MHz
• 7.9" W x 6.25" H x 1.25" D

Product Number: SSR00069

The Model XT-1 1-Channel Stationary Mid-range Transmitter is designed for use in various wireless remote control applications. When triggered with an external switch, the Model XT-1 transmitter will send a 10 watt, 27.255 MHz, digital encoded, FSK modulated, signal to its companion receiver. The receiver will verify the digital code, activate its output, and trigger the remote device.

The XT-1 transmitter has full supervision capabilities. If the status option is selected, the XT-1 sends hourly status signals to its receiver. If these signals cease, the receiver will indicate trouble by activating its status output after four hours. Contact supervision allows the receiver's output to follow the transmitter's input, staying activated as long as the transmitter input is activated. Alternately, an auto-restore option can be selected, causing a momentary receiver output each time the transmitter is activated. Either a N/O or N/C input (jumper selectable) can trigger the transmitter.

Power for the XT-1 transmitter can come from an external regulated 12 VDC, 2-Amp power supply (Linear Model T-1224DC) or from a 12-volt battery. A 3-amp fuse protects the unit from reverse power polarity. The XT-1 draws about 15 mA standby, and about two amps during transmissions. If the power supply voltage drops below 10.5 volts, a low battery message will be included with any signal transmitted, causing the receiver's low battery output to activate.

Two antennas (sold separately) are available for the XT-1. The Model ANT-1A is an 7-inch rubber duck antenna for short range applications (less than 1 mile). The ANT-1A is supplied with a CON-180A (straight) connector to mate the antenna to the transmitter. For a right angle antenna mounting, use a CON-90A right-angle connector with the CON-180A. The Model ANT-2 is a 3-foot whip antenna for use in long range or difficult installations where more range from the XT-1 is required. A common 9-foot 1/4 wave CB whip antenna can also be used with the XT-1 for maximum range.

Two 8-position switches set the unit's system code. This code must be matched in the XT-1's receiver. There are 65,536 different system codes possible. The 6-position option switch selects the transmitter's channel, receiver's bank (for XR-16 receiver only), and options for status and auto-restore transmissions.

The transmitter is housed in a rugged weather-resistant metal enclosure with a sturdy SO-239 antenna connector and a water-tight wiring strain relief bushing. During transmissions, the red operation indicator (visible through a window on the case) lights. If the XT-1's input voltage is low, the indicator will blink during transmissions.
Features

The Model XT-1H 1-Channel Handheld Mid-range Transmitter is designed for use in various wireless remote control applications. When activated, the XT-2H portable transmitter will send a 2 watt, 27.255 MHz, digital encoded, FSK modulated, signal to their companion receiver. The receiver will verify the digital code, activate its output, and trigger the remote device.

The Model XT-1H is a one-button, single channel transmitter. Each transmission is limited to a maximum of 30 seconds duration.

The XT-1H portable transmitter is powered by two 9-volt alkaline batteries in series, supplying 18 volts. During transmissions, the red operation indicator will light (visible through a window next to the antenna). If the transmitter's battery voltage is low, the indicator will blink during transmissions. The XT-1H transmitter has battery supervision capabilities. If the combined battery voltage drops below 12 volts, a low battery message will be included with any signal transmitted, causing the receiver's low battery output to activate. The test button next to the indicator sends a test transmission when pressed.

Two 8-position switches set the unit's system code. This code must be matched in the transmitter's companion receiver. There are 65,536 different system codes possible. The 4-position option switch selects the transmitter's channel and the receiver's bank (for the XR-16 receiver only).

Each transmitter is provided with a 6-inch rubber duck antenna and a removable belt clip.

• Up to two miles of line-of-sight range
• Over 64,000 Codes
• Includes belt clip
• Powered by two 9-volt batteries (included)
• RF frequency: 27.255 MHz
• 2.375" W x 12.25" H x 1.375" D