The Model LMT-1/303 Miniature Transmitter is a battery powered, portable, miniature pendant transmitter designed for use with Linear's MegaCode Format receivers. The transmitter can be used in a limitless number of wireless remote control applications. Pressing the button on the transmitter sends a digitally coded wireless signal to its companion receiver.

The LMT-1/303 is a one-button, one-code transmitter. Pressing the button sends the transmitter's code to the receiver. Press the button for a minimum of two seconds to insure receiver activation. The transmitter button has a positive click feel.

The LMT-1/303 transmitter is powered from a 12-Volt Type GP-23 battery with an expected battery life of about 1 year. The red test/operate indicator lights during operation. When the transmitter does not function, or its range decreases, replace the battery.

A detachable 30" neck chain is provided with each transmitter.

Features

• Famous "Panic Button" design
• 30-inch neck chain included
• Test/operate LED
• Type GP-23 12-volt alkaline battery supplied
• Megacode format
• RF frequency: 303.875 MHz
• 1.42" W x 2.2" H x 0.66" D

The Model ST-23A Supervised Bill Trap Transmitter is a battery powered cash drawer bill trap with a built-in transmitter designed for use with Linear's S1 Format receivers. This transmitter can be used in a variety of retail hold-up applications.

The ST-23A is concealed in a cash drawer under a stack of currency, with a single bait bill secured in its money clip. During a hold-up, the cashier removes the stack of currency along with the bait bill. When a bait bill is removed, the transmitter sends a 1-second digitally coded wireless signal to its companion receiver. Four additional 1-second signals are sent within the first minute after the bait bill is removed. When the bait bill is replaced, a restore signal is sent.

The ST-23A can send four different signals: alarm, restore, low battery, and status.

Inside the transmitter is a rolling ball that detects when the cash drawer opens and closes, this determines when status transmissions are sent. Because the transmitter's signal might be shielded in a closed cash drawer, the status signals are sent when the drawer is opened. Optionally, the ST-23A can transmit status signals once per hour regardless of motion.

The transmitter has a red test indicator which lights when a bill is in the trap and the test button is pressed. It also lights when the bait bill is inserted into the trap. For safety, the indicator doesn't light when the bait bill is removed. The test indicator will not light when pressing the test button with the bait bill removed.

The test button is disabled for 60-seconds after removing the bait bill. Pressing the test button without a bill in the trap sends an alarm signal. Pressing the test button with a bill in the trap sends a restore signal.

The unit is powered from two 2032 3-Volt lithium batteries with an expected battery life of up to two years. When the batteries get low, the test indicator will flash when the test button is pressed or when the bait bill is replaced.

Features

• Status reporting only when cash drawer is open
• Alarm, restore, test transmissions
• Lithium battery powered
• Test LED
• Transmit repeat feature ensures reliability
• S1 format
• RF frequency: 303.875 MHz
• 2.4" W x 4.5" H x 0.8" D

The Model TX-91 Supervised 2-Button, 3-Channel Handheld Transmitter is a supervised, digitally coded radio transmitter designed for use with Linear's SX Format receivers. Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The top button can be hidden with the top button cover supplied.

The TX-91 is a two-button, one-code transmitter. Pressing either the round button on the transmitter's front, or the small button on the transmitter's top will send the same signal.

Coding switches are not required or used in the TX-91 transmitter. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible.

The TX-91 is supervised for low battery and sends hourly status reports. Some receivers are able to use these signals, others are not. Receivers must be programmed to the transmitter code before system testing and operation. Refer to the receiver's instructions for details on operation and programming.

Each TX-91 is powered by two self-contained type 2032 3-volt lithium batteries (included). When the batteries voltage gets low, a low battery report is sent with any alarm or status report to notify the receiver. The red LED will blink when the transmitter is activated with low batteries.

A removable pocket clip and belt clip are provided for each transmitter. Either can be attached to the back of the transmitter allowing the unit to be clipped to shirt pocket or slid onto a belt.

Features

• Complete RF supervision
• Alarm, supervisory, and low battery transmissions
• Unique "Extra" top button
• High visibility operate LED
• Two type 2032 lithium batteries supplied
• Pocket and belt clip supplied
• SX format
• RF frequency: 303.875 MHz
• 1.6" W x 4.2" H x 0.8" D

The Model TX-92 Supervised 3-Button, 6-Channel Handheld Transmitter is a supervised, digitally coded radio transmitter designed for use with Linear's SX Format receivers. Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The top button can be hidden with the top button cover supplied.

The TX-92 is a three-button, six-code transmitter. Pressing either of the transmitter's front buttons sends codes one and two. Pressing the small button on the transmitter's top sends code three. Pressing both front buttons together sends code four. Pressing the transmitter's top button together with either front button will send codes five and six.

Coding switches are not required or used in the TX-92 transmitter. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible.

The TX-92 is supervised for low battery and sends hourly status reports. Some receivers are able to use these signals, others are not. Receivers must be programmed to the transmitter code before system testing and operation. Refer to the receiver's instructions for details on operation and programming.

Each TX-92 is powered by two self-contained type 2032 3-volt lithium batteries (included). When the batteries voltage gets low, a low battery report is sent with any alarm or status report to notify the receiver. The red LED will blink when the transmitter is activated with low batteries.

A removable pocket clip and belt clip are provided for each transmitter. Either can be attached to the back of the transmitter allowing the unit to be clipped to shirt pocket or slid onto a belt.

Features

• Complete RF supervision
• Alarm, supervisory, and low battery transmissions
• Unique "Extra" top button
• High visibility operate LED
• Two type 2032 lithium batteries supplied
• Pocket and belt clip supplied
• SX format
• RF frequency: 303.875 MHz
• 1.6" W x 4.2" H x 0.8" D

The Model TX-94 Supervised 5-Button 15-Channel Handheld Transmitter is a supervised, digitally coded radio transmitter designed for use with Linear's SX Format receivers. Pressing a button on the transmitter sends a digitally coded wireless signal to its companion receiver. To send a complete signal, press the transmitter button for a minimum of 2 seconds. The top button can be hidden with the top button cover supplied.

The TX-94 is a five-button, fifteen-code transmitter. Pressing one of the transmitter's front buttons sends codes one through four. Pressing the small button on the transmitter's top sends code five. Pressing the transmitter's top button together with each front button sends codes six through nine. Pressing the two top front buttons together sends code ten. Pressing the two bottom front buttons together sends code eleven. Pressing the two left front buttons together sends code twelve. Pressing the two right front buttons together sends code thirteen. Pressing the top left and bottom right front buttons together sends code fourteen. Pressing the bottom left and top right front buttons together sends code fifteen.

Coding switches are not required or used in the TX-94 transmitter. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible.

The TX-94 is supervised for low battery and sends hourly status reports. Some receivers are able to use these signals, others are not. Receivers must be programmed to the transmitter code before system testing and operation. Refer to the receiver's instructions for details on operation and programming.

Each TX-94 is powered by two self-contained type 2032 3-volt lithium batteries (included). When the batteries voltage gets low, a low battery report is sent with any alarm or status report to notify the receiver. The red LED will blink when the transmitter is activated with low batteries.

A removable pocket clip and belt clip are provided for each transmitter. Either can be attached to the back of the transmitter allowing the unit to be clipped to shirt pocket or slid onto a belt.

Features

• Complete RF supervision
• Alarm, supervisory, and low battery transmissions
• Unique "Extra" top button
• High visibility operate LED
• Two type 2032 lithium batteries supplied
• Pocket and belt clip supplied
• SX format
• RF frequency: 303.875 MHz
• 1.6" W x 4.2" H x 0.8" D

Model Number: WET-2

Product Number: AAE00215

The TMD-90 Supervised Passive Infrared Motion Detector is a passive infrared (PIR) motion detector with a built-in supervised, digitally-coded radio transmitter designed for security applications.

The PIR detects motion in its detection pattern by measuring the infrared emission levels of objects that it sees. If the infrared levels change quickly, as when a person moves across the detection pattern, the PIR will recognize the change as an intrusion.

A selectable pulse count circuit controls the PIR's triggering of the transmitter. As a person moves across the detection pattern, the PIR registers one pulse as each finger of the detection pattern is crossed. The TMD-90 counts these pulses. When the selected number of pulses occur during the selected time, the PIR will trigger the transmitter, sending an alarm signal. A lockout timer prevents the transmitter from triggering more often than once every 2 minutes when constant motion is detected. The pulse counting and timing options are selected with the OPTION switch.

The unit is supervised for low battery, alarm and status reporting. The TMD-90 is compatible with any Linear SX format supervised security receiver. The transmitter sends hourly status reports. A test report can be sent by pressing the test button.

Coding switches are not required or used in this transmitter. Each transmitter is pre-coded at the factory to a unique code. With the SX format, there are more than sixteen million codes possible.

The transmitter is powered by four AA 1.5-volt alkaline batteries (included) and can power the unit for up to 5 years. When the battery voltage gets low, a low battery report is sent to the receiver with any alarm, test or status report.

Features

• Dual-element pyroelectric sensor
• Fully supervised
• Tamper switch
• Walk test mode
• Adjustable pulse count
• Transmission delay feature
• Retransmission delay
• Multiple lens options
• Alkaline batteries supplied
• 5-Year battery life
• UL listed
• SX format
• RF frequency: 303.875 MHz
• 3.25" W x 5.75" H x 1.75" D