When the ARM-2 is used the additional power required for this relay module must be subtracted from the total circuit current available. See PFC- 2000RC Manual 5403521, DWG. #3521-1, Note 12 or PFC-4410 Manual 5403527, page 7, Output Circuits.
The ARM-2 Auxiliary Relay Module is a nonsupervised DPDT Relay designed to be activated by 24VDC Indicating and/or Releasing, polarity reversing circuits. The module can be used for fan shutdown, door release, elevator recall, etc. Note: One to three ARM-2 modules in the PFC- 2000RC or one to four ARM-2 modules in the PFC-4410 may be utilized to provide multiple auxiliary functions.
The module is to be mounted in the upper right hand corner of the panel. Connection to the panel is made via the 8 pin header mounted on the back side of the CA2Z.
The PS40-TM is the industrys FIRST AND ONLY completely pre-assembled low pressure test module for dry pipe and pre-action systems. The PS40-TM consists of the Potter PS40-2 supervisory pressure switch, BVL bleeder valve, and high quality easy to read pressure gauge all pre-assembled together with galvanized pipe.
The PS40-TM provides a fast and foolproof way to confirm the system meets the requirement of NFPA 72, 2007, 5.15.2.2 and to perform the test required by NFPA 25, 2007, 13.4.4.2.6. The PS40-TM also eliminates any possibility of accidentally tripping the dry pipe valve during testing. Closing the BVL bleeder valve isolates the PS40 and pressure gauge from the air source while exhausting the supervisory air pressure between the bleeder valve and the PS40. This can save hours of time waiting for pressure to bleed down then build back up, as is the case in the old conventional testing method.
General Description The PFC-100RC is a full featured single hazard releasing control panel for use on pre-action and deluge type sprinkler systems. The model PFC-100RC is Underwriters Laboratories Listed and complies with UL Standard 864 for Local Control Units for Releasing Service. It is designed to be compatible with the requirements of NFPA- 72, NFPA-12, NFPA-12A, NFPA-12B, NFPA-13 and NFPA-17. The PFC-100RC is FM, NYMEA and CSFM Approved. The PFC-100RC features LED indicators for AC, ALARM, TROUBLE, SILENCE, and SUPERVISORY conditions that are visible with the door closed. Operator controls are provided for RESET, SILENCE, and RELEASE CIRCUIT DISABLE. Thirteen on board LED indicators provide extensive diagnostic ability to ease troubleshooting. Alarm and trouble relays are provided to interface with auxiliary equipment. Dimensions: 18 1/4" X 14 1/4" X 4 3/4" The PFC-100RC is housed in a steel cabinet with removable door and key lock. Standard finish is off-white with grey and red trim. Red cabinets with black and white trim are also available. A matching bezel is available as an option for semi-flush mounting in a wall. The cabinet will house up to a 12AH standby battery which is capable of powering the unit in excess of 90 hours.
Features One Initiating Device Circuit Selectable Class A or Class B One Class B Circuit for dry contact devices One 500mA Class B Indicating Circuit One 1 Amp Class B Releasing Circuit One Class B Supervisory Circuit 2 Amps Alarm and Trouble Contacts 200mA Auxiliary Power Output Supervised Integral Battery Charger Supports 2 or 4-Wire Detectors Field Selectable Pre-Discharge and Releasing Circuit Times
PL-PFC100RC
The PL-PFC100RCW REPLACES PL-PFC100RW
PL-PFC4410WH
PFC4410-RC RELEASING CONTROL PANEL DIMENSIONS: 18 1/4" X 14 1/4" X 4 3/4"gUL Listed, FM Approved, NYMEA Accepted, CSFM Approved
The Potter Model PFC-4410-RC is a microprocessor based multihazard releasing control panel for use on pre-action and deluge type sprinkler systems as well as chemical extinguishing systems. The model PFC-4410-RC is Underwriters Laboratories Listed and complies with UL Standard 864 for Local Control Units for Releasing Service. It is designed to be compatible with the requirements of: NFPA-12, NFPA-12A, NFPA-13, NFPA-15, NFPA-16, NFPA-17, NFPA-17A, NFPA-72, NFPA-750, and NFPA-2001.
The PFC-4410-RC is housed in a steel cabinet with removable door and key lock. Standard fi nish is off-white with gray and red trim. Red cabinets with black and white trim are also available. A matching bezel is available as an option for semi-fl ush mounting in a wall. The cabinet will house up to a 12AH standby battery which is capable of powering the unit in excess of 90 hours.
Features: Multi-Hazard Operation Supervised Microprocessor 32 Character Alpha-Numeric LCD Display Custom Banner Message Text Custom Zone Description Text On Board Menu Driven Programming Controls Releasing Circuits Protected From False Activation Four Class B Initiating Circuits One Class B Supervisory Circuit Four Class B Output Circuits Programmable Cross Zoning Continuous or Timed Discharge 40 Event History Buffer Walktest with Automatic Time-out Alarm, Trouble and Supervisory Relays Optional Class A Initiating Zone Module Optional Class A Output Zone Module 19 Standard Programs in Panel Memory Password Protection for all Programming 24 Hour Clock Supervised Remote annunciator output Suitable for chemical or waterbased extinguishing Programmable 0-60 second pre-discharge timer* Programmable 0-30 second manual release pre-discharge timer* One Class B Abort circuit* Three Abort modes* * Available in Chemical mode only
PL-PFC4410RC REPLACES PL-PFC4410 & REPLACES PL-PFC2000RC
PFC-4410-RC Water OR Agent Extinguishing Panel - Potter Electric Signal Company announces the release of our new PFC-4410-RC Releasing Panel. Our Water OR Chemical based extinguishing panel includes 4 Class B programmable initiating zones, 4 programmable Class B outputs, and 20 pre-configured programs. This single or dual hazard panel is also compatible with 3500 feet of Linear Heat Detection per zone. The new, innovative technology of the PFC-4410-RC allows you to use the same panel to control water OR chemical discharge. The PFC-4410-RC is UL, CSFM, NYMEA Listed, and FM approved.
