You are here: Home > Shop Brands > TAKEX > Security > Passive Infrared Sensors (PIRs) > Indoor Wall-Mount Sensors
We found 12 results matching your criteria.
Sort By:
Page of 1
Napco GEM-WP I - GEM-RECV8 8-Point Receiver/Interface + GEM-TRANS2 - Wireless Window / Door transmitters, White + Keyfob - GEMWPI Napco GEM-WP II - GEM-RECV8 8-Point Receiver/Interface + GEM-TRANS2 - Wireless Window / Door transmitters, White + GEM-PIR Wireless PIR + Keyfob - GEMWPII
GEM-RECV Series receivers are the hardwired interface to Napco's Wireless-Ready TM Control Panels. The wireless system comprises a compatible GEM-Series control panel, at least one GEM-RECV receiver and one or more companion GEMSeries transmitters. The transmitters may be wireless smoke detectors, space-protection devices, window/door sensors, or other devices that report zone status and supervision information to the receiver without the use of wires.
Napco GEM-TRANS2 - Wireless Window / Door transmitter, White - GEM-TRANS2
GEM-RECV Series receivers are the hardwired interface to Napco's Wireless-Ready TM Control Panels. The wireless system comprises a compatible GEM-Series control panel, at least one GEM-RECV receiver and one or more companion GEMSeries transmitters. The transmitters may be wireless smoke detectors, space-protection devices, window/door sensors, or other devices that report zone status and supervision information to the receiver without the use of wires.
Napco GEM-TRANS2 - Wireless Window / Door transmitter, White - GEM-TRANS2
Napco GEM-WP III - GEM-RECV8 8-Point Receiver/Interface + 3 x GEM-TRANS2 - Wireless Window / Door transmitters, White + GEM-PIR Wireless PIR + Keyfob - GEMWPIII Takex America (Pulnix) PA-450 Wide Angle (35') Dual PIR Sensor
GEM-RECV Series receivers are the hardwired interface to Napco's Wireless-Ready TM Control Panels. The wireless system comprises a compatible GEM-Series control panel, at least one GEM-RECV receiver and one or more companion GEMSeries transmitters. The transmitters may be wireless smoke detectors, space-protection devices, window/door sensors, or other devices that report zone status and supervision information to the receiver without the use of wires.
Napco GEM-TRANS2 - Wireless Window / Door transmitter, White - GEM-TRANS2
  • 36’ x 84° Wide angle
  • Fresnel lens
  • Look-Down Zone
  • Immunity against radio frequnecy, power line noise
  • LED on/off
  • Alarm Memory
  • 10 to 18VDC, UL Listed
  • Detection System: Passive Infrared
  • Modulation Pulse Count
  • Protection Distance Indoors: 36ft
  • Alarm Output: Silent N/O or N/C Selectable
  • Tamper Output Circuit
  • Takex America (Pulnix) PA-450PI  Wide Angle (35') Dual PIR Sensor, Pet-Immune Takex America (Pulnix) PA-460  Vertical Curtain (55') Dual PIR Sensor
  • Pet-Immune up to 40 lbs.
  • 36’ x 84° Wide angle
  • Fresnel lens
  • Look-Down Zone
  • Immunity against radio frequnecy, power line noise
  • LED on/off
  • Alarm Memory
  • 10 to 18VDC, UL Listed
  • Detection System: Passive Infrared
  • Modulation Pulse Count
  • Protection Distance Indoors: 36ft
  • Alarm Output: Silent N/O or N/C Selectable
  • Tamper Output Circuit
  • 55’ Vertical curtain,
  • Fresnel lens,
  • Silent N/O or N/C selectable output,
  • Tamper Circuit,
  • LED on/off,
  • Alarm Memory,
  • 10 to 18VDC,
  • Newly developed 4-bit exclusive microprocessor
  • Immunity against radio frequency and power-line noise
  • Completely noiseless
  • UL listed
  • Takex America (Pulnix) PA-470L Wide-Angle / Long-Range PIR Sensor Takex America (Pulnix) PA-480S Wide-Angle / Long-Range PIR Sensor
    features the unique Fuzzy Logic Processing System - the state-of-the-art processing system that stimulates the human decision process as it compares various information such as size and temperature differential. This reduces false alarms while maintaining a high-detection capability.

    The PA470L also includes a wide-angle / long-range pattern option selectable during installation. A zone changeover switch sets the detection pattern to match the lens pattern when lens is changed. In addition, a trouble alarm sounds when the sensor detects a drop in supply voltage.

  • 53’ x 84° Wide angle or 66’ Long range (includes both Fresnel lenses)
  • Quad
  • “Fuzzy Logic” signal processing
  • N/O or N/C selectable output
  • Tamper Circuit
  • LED on/off
  • 9 to 18VDC
  • Alarm Memory
  • Remote LED control
  • Takex's PA-480S features the unique Fuzzy Logic Processing System - the state-of-the-art processing system that stimulates the human decision process as it compares various information such as size and temperature differential. This reduces false alarms while maintaining a high-detection capability.

    The PA480S also includes a wide-angle / long-range pattern option selectable during installation by convenient fresnel lens replacement A zone changeover switch sets the detection pattern to match the lens pattern when lens is changed. In addition, a trouble alarm sounds when the sensor detects a drop in supply voltage.

    Wall Mount 180 degree coverage - two twin elements cover 90 degrees each to create a full 180 degree pattern. Each 90 degree area can be vertically adjusted to create the required coverage pattern.

  • 53’ x 84° Wide angle or 66’ Long range (includes both Fresnel lenses)
  • Quad
  • “Fuzzy Logic” signal processing
  • N/O or N/C selectable output
  • Tamper Circuit
  • LED on/off
  • 9 to 18VDC
  • Alarm Memory
  • Remote LED control
  • Takex America (Pulnix) PA-4810  Mirror Optic "Fuzzy Logic" Wide-Angle PIR Sensor Takex America (Pulnix) PA-4820  Mirror-Optic "Fuzzy Logic" Wide-Angle PIR Sensor, 83' Long-Range
    ORIGINAL QUAD ELEMENT + NEW SIGNAL PROCESSING (FUZZY LOGIC)
    PULNiX's original quad pyroelectric sensor improves sensitivity. This newly developed original pyroelectric sensor coupled with new Fuzzy Logic provides high catchability.

    MIRROR OPTICS AND EASY AIMING SYSTEM
    Precise mirror optics and new quad element assure high sensitivity and high reliability. As mirror and head unit move together, area adjustment does not reduce/blur sensitivity. PULNiX original view finder assures precise and quick adjustment.

    TROUBLE ALARM
    Unit monitors the following functions. When a trouble condition is detected. the alarm LED lights and trouble alarm is initiated.
  • Unit trouble ...A trouble alarm triggers when inner circuitry/wiring is damaged/broken.
  • Low voltage ...A trouble alarm triggers when sensor detects a drop in supply voltage.
  • Failure to replace... A trouble alarm triggers when head unit is not replaced after adjustment is completed.

    FINE MOTION DETECTION
    Unit can be adjusted from quad element sensing to two twin element by built -in switch for situations where close range detection is desirable.
  • Alarm LED disable (ON IOFF)
  • Alarm contact changeover (N.C.I N.O.)
  • Sensitivity adjustment (60%, 80%,100%, 120%)

    ALARM MEMORY
    Units contain special circuitry to indicate an alarm has been activated during armed period. Especially useful when more than one unit is used per zone.

    REMOTE LED CONTROL
    Allows the LED to be enabled/disabled via the controlpanel.

  • 40’ x 84° Wide angle
  • Adjustable Mirror Optic
  • Quad,
  • “Fuzzy Logic” signal processing
  • N/O or N/C selectable output
  • Tamper Circuit
  • LED on/off,
  • 10 to 30VDC
  • ORIGINAL QUAD ELEMENT + NEW SIGNAL PROCESSING (FUZZY LOGIC)
    PULNiX's original quad pyroelectric sensor improves sensitivity. This newly developed original pyroelectric sensor coupled with new Fuzzy Logic provides high catchability.

    MIRROR OPTICS AND EASY AIMING SYSTEM
    Precise mirror optics and new quad element assure high sensitivity and high reliability. As mirror and head unit move together, area adjustment does not reduce/blur sensitivity. PULNiX original view finder assures precise and quick adjustment.

    TROUBLE ALARM
    Unit monitors the following functions. When a trouble condition is detected. the alarm LED lights and trouble alarm is initiated.
  • Unit trouble ...A trouble alarm triggers when inner circuitry/wiring is damaged/broken.
  • Low voltage ...A trouble alarm triggers when sensor detects a drop in supply voltage.
  • Failure to replace... A trouble alarm triggers when head unit is not replaced after adjustment is completed.

    FINE MOTION DETECTION
    Unit can be adjusted from quad element sensing to two twin element by built -in switch for situations where close range detection is desirable.
  • Alarm LED disable (ON IOFF)
  • Alarm contact changeover (N.C.I N.O.)
  • Sensitivity adjustment (60%, 80%,100%, 120%)

    ALARM MEMORY
    Units contain special circuitry to indicate an alarm has been activated during armed period. Especially useful when more than one unit is used per zone.

    REMOTE LED CONTROL
    Allows the LED to be enabled/disabled via the controlpanel.

  • 83' Long-Range
  • Adjustable Mirror Optic
  • Quad,
  • “Fuzzy Logic” signal processing
  • N/O or N/C selectable output
  • Tamper Circuit
  • LED on/off,
  • 10 to 30VDC
  • Takex America (Pulnix) PA-5312 Wide Angle (40') Wall/Ceiling Mount PIR Sensor Takex America (Pulnix) PA-5325 Indoor Ceiling-Mount IR Sensor, 82' Long-Range Vertical Curtain
    The high-performance and new design of the PA-5312's dual twin element, optical unit and signal-pro cessing circuitry create a high-density 40' wide-angle protection area.

    The unit can be adjusted from quad-element sensing to twin-element sensing, which results in double the number of sensitive zones for situations where close-range detection is desirable. (Highest sensitivity setting)

    The unit conducts a checking test of alarm contact whenever an alarm is initiated. An alarm LED flashes if the contact is short or damaged by induced lightning, etc.

    Built-in alarm memory LED informs you which sensor triggered an alarm during an armed condition when two or more sensors are connected on the same line.

    Trouble is indicated by continuous alarm output and continuous lighting of the alarm LED.

  • Low voltage - Trouble alarm triggers when sensor supply voltage drops down to approx. 8.5V DC
  • Unit trouble - Trouble alarm triggers when inner circuit / wiring is damaged / broken.
  • Failure to replace - Trouble alarm triggers when the aiming device is failed to be replaced after aiming is completed.

  • 40' x 84° Wide-angle
  • Wall or Ceiling mount,
  • Separate base and sensor head.
  • Adjustable mirror optic QUAD with aiming LED.
  • Pulse count & sensitivity adjustment with Slight Motion detection.
  • N/O or N/C selectable output.
  • Alarm contact check feature with trouble output,
  • Tamper circuit,
  • LED on/off.
  • Alarm memory,
  • 9.5V to 30VDC
  • Quad elements coupled with new signal processing (discriminating temperature differential information and object size information) provide high "catchability."
  • Twin-element optical unit and signal-processing circuitry provide high-density protection areas.
  • Unit can be adjusted from quad elements sensing to twin element sensing, resulting in double the number of sensetive zones.
  • Includes checking test of alarm contact whenever an alarm is initiated.
  • Includes built-in alarm memory(indicates which sensor was activated) and trouble alarm to signal unit trouble or low voltage

  • 82' Long-range vertical curtain
  • Wall or Ceiling mount,
  • Separate base and sensor head.
  • Adjustable mirror
  • Optic QUAD with aiming LED.
  • Pulse count & sensitivity adjustment with Slight Motion detection.
  • N/O or N/C selectable output.
  • Alarm contact check feature with trouble output
  • Tamper circuit
  • LED on/off.
  • Alarm memory,
  • 9.5V to 30VDC

  •    
     
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please