You are here: Home > Shop Brands > Gentex Corp. > Fire Protection > Audible/Visual Signaling Appliances > Photoelectric Smoke Alarm with Visual Signaling Appliance
We found 5 results matching your criteria.
Sort By:
Page of 1
Gentex Corp 9070231 Photoelectric Smoke Detector with Visual Signaling Appliance, Wall-Mount, Tandem Up to 6 Units, Form 'C" Contacts Gentex Corp 9070232 Photoelectric Smoke Detector with Visual Signaling Appliance, Ceiling Mount, Tandem Up to 6 Units, Form "C" Relay
The 710/713CS/LS and 7109/7139CS/LS Photoelectric Single Station Smoke Alarms are designed to give reliable early warning of the presence of smoke where both audible and visual alarms are required. The series features a 90dBA solid state piezo signal and a 177 Candela strobe with “FIRE” lettering. The strobe is listed per UL 1971.

The 713/7139 Series provides the temporal 3 evacuation tone as a standard feature. When testing the 713/7139 Series it may take up to 16 seconds longer to go in or out of alarm. The smoke alarm operates on the light scattering principle, a superior method of detection in smoldering fires, utilizing a pulsing LED light source and a photodiode sensor in a fully screened sensing chamber. Every 4 to 5 seconds the pulsing LED emits an infrared beam that by passes the photodiode under normal conditions.

However, when smoke enters the sensing chamber, the infrared beam is deflected onto the sensor by the smoke particles. The LED pulse rate increases to 8 times the normal rate, and after the photodiode confirms that smoke is present for 2 consecutive pulses, it will produce the signal necessary to trip an alarm.

Upon activation, the alarm will emit a 90dBA local audible signal and activate the high intensity strobe. During the alarm period the strobe will flash at a brightness of 177 Candela 60 times per minute. After the smoke has cleared from the detector, the unit will revert to the normal stand-by condition.

Features
  • 177 Candela Rating (UL1971)
  • Solid State 90dBA Horn
  • Temporal 3 Evacuation Sounding Device (713CS/LS & 7139CS/LS Series)
  • Nominal 2.5% Sensitivity
  • 5-to-1 Signal-to-Noise Ratio
  • Full Function Test Switch—Patented Three Position Test
  • Fully Insect Screened
  • Quick-Disconnect Wiring Harness (CS Models)
  • 9 VDC Battery Back-Up (7109/7139CS/LS) w/Audible Low Battery Chirp (Visual Does Not Operate on Battery Back-Up)
  • Form C Auxiliary Relay Contacts for Remote Annunciation (CS Models)
  • Tandem Connection up to 6 Detectors Per System (CS Models)
  • 9 Foot Line Cord (LS Models)
  • Mounting Hardware
  • Warranty is 1 Year From Date of Purchase
  • Dry Contacts Will Activate From the Tandem Wire
  • Relays Operate on Battery Back-Up, Visual Does Not Operate
  • Horn Frequency 3100Hz (Nominal)
  • The 710/713CS/LS and 7109/7139CS/LS Photoelectric Single Station Smoke Alarms are designed to give reliable early warning of the presence of smoke where both audible and visual alarms are required. The series features a 90dBA solid state piezo signal and a 177 Candela strobe with “FIRE” lettering. The strobe is listed per UL 1971.

    The 713/7139 Series provides the temporal 3 evacuation tone as a standard feature. When testing the 713/7139 Series it may take up to 16 seconds longer to go in or out of alarm. The smoke alarm operates on the light scattering principle, a superior method of detection in smoldering fires, utilizing a pulsing LED light source and a photodiode sensor in a fully screened sensing chamber. Every 4 to 5 seconds the pulsing LED emits an infrared beam that by passes the photodiode under normal conditions.

    However, when smoke enters the sensing chamber, the infrared beam is deflected onto the sensor by the smoke particles. The LED pulse rate increases to 8 times the normal rate, and after the photodiode confirms that smoke is present for 2 consecutive pulses, it will produce the signal necessary to trip an alarm.

    Upon activation, the alarm will emit a 90dBA local audible signal and activate the high intensity strobe. During the alarm period the strobe will flash at a brightness of 177 Candela 60 times per minute. After the smoke has cleared from the detector, the unit will revert to the normal stand-by condition.

    Features
  • 177 Candela Rating (UL1971)
  • Solid State 90dBA Horn
  • Temporal 3 Evacuation Sounding Device (713CS/LS & 7139CS/LS Series)
  • Nominal 2.5% Sensitivity
  • 5-to-1 Signal-to-Noise Ratio
  • Full Function Test Switch—Patented Three Position Test
  • Fully Insect Screened
  • Quick-Disconnect Wiring Harness (CS Models)
  • 9 VDC Battery Back-Up (7109/7139CS/LS) w/Audible Low Battery Chirp (Visual Does Not Operate on Battery Back-Up)
  • Form C Auxiliary Relay Contacts for Remote Annunciation (CS Models)
  • Tandem Connection up to 6 Detectors Per System (CS Models)
  • 9 Foot Line Cord (LS Models)
  • Mounting Hardware
  • Warranty is 1 Year From Date of Purchase
  • Dry Contacts Will Activate From the Tandem Wire
  • Relays Operate on Battery Back-Up, Visual Does Not Operate
  • Horn Frequency 3100Hz (Nominal)
  • Gentex Corp 9070235 Photoelectric Smoke Detector with Visual Signaling Appliance, Wall Mount, Tandem Up to 6 Units, Form "C" Relay Gentex Corp 9070236 Photoelectric Smoke Detector with Visual Signaling Appliance, Ceiling Mount, Tandem Up to 6 Units, Form "C" Relay
    The 710/713CS/LS and 7109/7139CS/LS Photoelectric Single Station Smoke Alarms are designed to give reliable early warning of the presence of smoke where both audible and visual alarms are required. The series features a 90dBA solid state piezo signal and a 177 Candela strobe with “FIRE” lettering. The strobe is listed per UL 1971.

    The 713/7139 Series provides the temporal 3 evacuation tone as a standard feature. When testing the 713/7139 Series it may take up to 16 seconds longer to go in or out of alarm. The smoke alarm operates on the light scattering principle, a superior method of detection in smoldering fires, utilizing a pulsing LED light source and a photodiode sensor in a fully screened sensing chamber. Every 4 to 5 seconds the pulsing LED emits an infrared beam that by passes the photodiode under normal conditions.

    However, when smoke enters the sensing chamber, the infrared beam is deflected onto the sensor by the smoke particles. The LED pulse rate increases to 8 times the normal rate, and after the photodiode confirms that smoke is present for 2 consecutive pulses, it will produce the signal necessary to trip an alarm.

    Upon activation, the alarm will emit a 90dBA local audible signal and activate the high intensity strobe. During the alarm period the strobe will flash at a brightness of 177 Candela 60 times per minute. After the smoke has cleared from the detector, the unit will revert to the normal stand-by condition.

    Features
  • 177 Candela Rating (UL1971)
  • Solid State 90dBA Horn
  • Temporal 3 Evacuation Sounding Device (713CS/LS & 7139CS/LS Series)
  • Nominal 2.5% Sensitivity
  • 5-to-1 Signal-to-Noise Ratio
  • Full Function Test Switch—Patented Three Position Test
  • Fully Insect Screened
  • Quick-Disconnect Wiring Harness (CS Models)
  • 9 VDC Battery Back-Up (7109/7139CS/LS) w/Audible Low Battery Chirp (Visual Does Not Operate on Battery Back-Up)
  • Form C Auxiliary Relay Contacts for Remote Annunciation (CS Models)
  • Tandem Connection up to 6 Detectors Per System (CS Models)
  • 9 Foot Line Cord (LS Models)
  • Mounting Hardware
  • Warranty is 1 Year From Date of Purchase
  • Dry Contacts Will Activate From the Tandem Wire
  • Relays Operate on Battery Back-Up, Visual Does Not Operate
  • Horn Frequency 3100Hz (Nominal)
  • The 710/713CS/LS and 7109/7139CS/LS Photoelectric Single Station Smoke Alarms are designed to give reliable early warning of the presence of smoke where both audible and visual alarms are required. The series features a 90dBA solid state piezo signal and a 177 Candela strobe with “FIRE” lettering. The strobe is listed per UL 1971.

    The 713/7139 Series provides the temporal 3 evacuation tone as a standard feature. When testing the 713/7139 Series it may take up to 16 seconds longer to go in or out of alarm. The smoke alarm operates on the light scattering principle, a superior method of detection in smoldering fires, utilizing a pulsing LED light source and a photodiode sensor in a fully screened sensing chamber. Every 4 to 5 seconds the pulsing LED emits an infrared beam that by passes the photodiode under normal conditions.

    However, when smoke enters the sensing chamber, the infrared beam is deflected onto the sensor by the smoke particles. The LED pulse rate increases to 8 times the normal rate, and after the photodiode confirms that smoke is present for 2 consecutive pulses, it will produce the signal necessary to trip an alarm.

    Upon activation, the alarm will emit a 90dBA local audible signal and activate the high intensity strobe. During the alarm period the strobe will flash at a brightness of 177 Candela 60 times per minute. After the smoke has cleared from the detector, the unit will revert to the normal stand-by condition.

    Features
  • 177 Candela Rating (UL1971)
  • Solid State 90dBA Horn
  • Temporal 3 Evacuation Sounding Device (713CS/LS & 7139CS/LS Series)
  • Nominal 2.5% Sensitivity
  • 5-to-1 Signal-to-Noise Ratio
  • Full Function Test Switch—Patented Three Position Test
  • Fully Insect Screened
  • Quick-Disconnect Wiring Harness (CS Models)
  • 9 VDC Battery Back-Up (7109/7139CS/LS) w/Audible Low Battery Chirp (Visual Does Not Operate on Battery Back-Up)
  • Form C Auxiliary Relay Contacts for Remote Annunciation (CS Models)
  • Tandem Connection up to 6 Detectors Per System (CS Models)
  • 9 Foot Line Cord (LS Models)
  • Mounting Hardware
  • Warranty is 1 Year From Date of Purchase
  • Dry Contacts Will Activate From the Tandem Wire
  • Relays Operate on Battery Back-Up, Visual Does Not Operate
  • Horn Frequency 3100Hz (Nominal)
  • Gentex Corp 9070239 Photoelectric Smoke Detector with Visual Signaling Appliance, Wall Mount, Tandem Up to 6 Units, Form "C" Relay, 9ft. Line Cord
    The 710/713CS/LS and 7109/7139CS/LS Photoelectric Single Station Smoke Alarms are designed to give reliable early warning of the presence of smoke where both audible and visual alarms are required. The series features a 90dBA solid state piezo signal and a 177 Candela strobe with “FIRE” lettering. The strobe is listed per UL 1971.

    The 713/7139 Series provides the temporal 3 evacuation tone as a standard feature. When testing the 713/7139 Series it may take up to 16 seconds longer to go in or out of alarm. The smoke alarm operates on the light scattering principle, a superior method of detection in smoldering fires, utilizing a pulsing LED light source and a photodiode sensor in a fully screened sensing chamber. Every 4 to 5 seconds the pulsing LED emits an infrared beam that by passes the photodiode under normal conditions.

    However, when smoke enters the sensing chamber, the infrared beam is deflected onto the sensor by the smoke particles. The LED pulse rate increases to 8 times the normal rate, and after the photodiode confirms that smoke is present for 2 consecutive pulses, it will produce the signal necessary to trip an alarm.

    Upon activation, the alarm will emit a 90dBA local audible signal and activate the high intensity strobe. During the alarm period the strobe will flash at a brightness of 177 Candela 60 times per minute. After the smoke has cleared from the detector, the unit will revert to the normal stand-by condition.

    Features
  • 177 Candela Rating (UL1971)
  • Solid State 90dBA Horn
  • Temporal 3 Evacuation Sounding Device (713CS/LS & 7139CS/LS Series)
  • Nominal 2.5% Sensitivity
  • 5-to-1 Signal-to-Noise Ratio
  • Full Function Test Switch—Patented Three Position Test
  • Fully Insect Screened
  • Quick-Disconnect Wiring Harness (CS Models)
  • 9 VDC Battery Back-Up (7109/7139CS/LS) w/Audible Low Battery Chirp (Visual Does Not Operate on Battery Back-Up)
  • Form C Auxiliary Relay Contacts for Remote Annunciation (CS Models)
  • Tandem Connection up to 6 Detectors Per System (CS Models)
  • 9 Foot Line Cord (LS Models)
  • Mounting Hardware
  • Warranty is 1 Year From Date of Purchase
  • Dry Contacts Will Activate From the Tandem Wire
  • Relays Operate on Battery Back-Up, Visual Does Not Operate
  • Horn Frequency 3100Hz (Nominal)
  •    
     
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please