You are here: Home > Shop Brands > Elk > Unique Automation Accessories
We found 10 results matching your criteria.
Unique Automation Accessories
Sort By:
Page of 1
ELK   WSV - Water Shutoff Valve ELK ELK-MA100 iButton Touchkey Reader & Interface Pack
The ELK-WSV is a Professional Grade, electrically operated water shutoff valve for both residential and commercial use. Used in conjunction with an automation controller, leak detection devices, or a simple manual pushbutton, the WSV can easily and conveniently shut off the main water supply to the building. Unlike competitors. units, the ELK-WSV is a stainless steel, 1. full bore, ball valve with commercial grade seats and seals. It is a non-restricting valve which meets the approvals of state and municipal water authorities. The motorized actuator has a permanently lubricated gear drive with sufficient torque to open or close the valve under high pressure or after long periods of inactivity. The ELK-WSV valve can be operated via a simple 12 Volt DC input from a security or automation controller such as the ELK-M1 Gold or M1EZ8. It can also be attached directly to a 12Vdc power source through a SPDT Emergency Pushbutton or "Easy" button for manual control. Operating time from fully open to fully closed is less than 4 seconds.
FEATURES:
  • Rapid Action - Opening or Closing

  • Provides Remote Shut off of Main Water Supply

  • SS Ball Valve is Safe for Drinking Water

  • Integrates to Security or Automation Controller (e.g. Elk-M1 Gold or M1EZ8)

  • Can be Integrated with a Simple "Easy" Button

  • Can be Integrated with a Wireless Receiver and Wireless Pushbutton

  • Simple 12 VDC, Four (4) Conductor Hookup

  • Valve Direction/Water Flow Indication


SPECIFICATIONS:

Actuator:

  • Operates from 12 Volts DC

  • Min Rec. Power Supply: 12VDC, 1 Amp

  • Current Draw: ~500mA nominal, 1 Amp peak

  • Actuating Speed: < 4 seconds

  • Torque: 1.25 in. lbs.

  • Connections: 18 gauge, 4 conductor cord

Valve:

  • Full Port, 2-way Ball Valve

  • Stainless Steel Grade 316

  • 1" NPT threaded pipe connections


Overall Dimensions: 9" H x  5.75" W x 4" D

ELK ELK-MA100 iButton Touchkey Reader & Interface Pack

iButton Touchkey Reader & Interface Pack contains two accessory components that allow the ELK Magic Module (ELK-MM443(S)) to read iButton Touchkeys from Dallas Semiconductor. This enables the Magic Module (ELK-MM443(S)) to be used as an economical access controller, time-attendance functions, etc. The small “dime sized” iButton is a rugged memory device containing a uniquely readable “non-repeating” serial number. The iButton Touchkey Reader Interface connects to the Magic Module through an 8 conductor modular cable (included). Applications include: high security access control, simple on/off switching, password authentication, etc.

  • SKU: ELK-MA100
  • Interface (ELK-MA190) with 6 ft. Modular Cord.
  • Reader Probe (ELK-MA110), Two-Wire, with Stainless Steel 2" x 4" Wall Mount Plate.
  • Probe Can Be Up To 650' From Reader.
  • Over voltage protection on Data Lines.
  • Operating Power supplied from Magic Module.
  • Compact easy to mount enclosure.
  • Lifetime Limited Warranty.
  • ELK ELK-MA101 iButton Touchkeys 10pcs. ELK ELK-MB485 RS-232 to RS-485 Data Converter
    ELK ELK-MA101 iButton Touchkeys 10pcs.

    The ELK-MA101 is a package of 10 low cost electronic iButton Touchkeys with key ring holders used with Access Control Readers.

    Features:

  • Low Cost Electronic Keys for Access Control applications.
  • Each Key contains unique 48-bit serial number + 8-bit CRC checking.
  • Durable Stainless Steel Case withstands harsh environments.
  • Angled Snap-In Key Holder.
  • Can be attached to a key ring.
  • Packaged in Reusable Poly Storage Box.
  • Can be used with Dallas 1-Wire™ Readers.
  • ELK ELK-MB485 RS-232 to RS-485 Data Converter

    The ELK-MB485 is used to communicate between a personal computer and an ELK Magic Module(ELKMM443). The ELK-MB485 converts the computer's RS-232 Serial Data to RS-485 Data which is used by the ELK Magic Module series of products. This allows programs to be downloaded into the Magic Modules. Input and Output status can be displayed and controlled from the computer.

  • SKU: ELK-MB485
  • Converts RS-232 to RS-485 Data.
  • Visual Power Indicator LED.
  • 9 Pin Serial D-Connector.
  • Terminals for 4-Wire Data Bus.
  • Quick Connect 4-Wire Data Bus Cable.
  • Lifetime Limited Warranty.
  • ELK ELK-MK485 Magic Module Programming Kit ELK ELK-MM220 Magic Module Programmable Controller
    ELK ELK-MK485 Magic Module Programming Kit

  • SKU: ELK-MK485

    This kit is the same as the ELK-MK400, less the Magic Module™ (ELK-MM443). It's for Magic Module™ owners that need to edit a Magic Module™ program. This kit contains hardware and software for creating, editing, and downloading Magic Module™ programs using a personal computer.

    Magic Module™ programs are transferred from your PC to the Magic Module™ using the PC’s serial port and an RS-232-to-RS-485 Data Converter module (ELK-MB485). Once programmed, the Magic Module™ can be disconnected from the PC for stand alone applications. All programming is stored in non-volatile memory.

  • Data Bus Interface (ELK-MB485)
  • ELK Code Editor / Application Writer Software
  • 12 Volt D.C. Plug-in Power Supply
  • 9 pin Serial Port Cable
  • RS-485 Data Bus Ribbon Cable
  • Cable to program ELK-MM220 modules
  • Instruction Manual
  • ELK ELK-MM220 Magic Module Programmable Controller

    The Magic Module (ELK-MM220) is a two digital input, two form C relay output programmable controller. It may be used as a stand alone field programmable controller in a vast array of applications from timers, single zone security system, pulse stretcher, simple process controllers, etc. The MM220 comes factory pre-programmed as a single zone security system and can be reprogrammed by using a personal computer. The MM220 program is stored into re-programmable Electrically Erasable Programmable Read Only Memory (EEProm memory). The ELK Starter Kit (ELK-MK400) contains components and software needed for programming.

  • SKU: ELK-MM220
  • Two Digital Inputs.
  • Two Relay Outputs (jumper programmable “transistor open collector” output on relay 2).
  • 4096 program bytes using SIMPLE programming language.
  • 4 general purpose Counters, range 0 to 255 counts.
  • 4 general purpose Timers, range 1/10 second to over 255 hours.
  • Program stored in non-volatile EEProm memory.
  • Surface Mount ABS Enclosure with Snap-On Cover.
  • Lifetime Limited Warranty.
  • ELK ELK-MM447 Magic Module Automation Controller (MM443) with Built-in Voice Annunciator (MV480) & Caddx Security Interface (ML8) ELK 930 Doorbell and Telephone Ring Detector
    ELK ELK-MM447 Magic Module Automation Controller (MM443) with Built-in Voice Annunciator (MV480) & Caddx Security Interface (ML8)

    The MM447 product is a Magic Module (MM443), a Recordable Voice Annunciator (MV480), and a Caddx NX Security Interface (ML8) integrated onto a single printed circuit board. It was specifically designed to mount into a Caddx NX series Control allowing for quicker and easier implementation of integration and automation applications such as the popular HomeControl.

  • SKU: ELK-MM447 MM443 Programmable Logic Controller
  • Four (4) supervised inputs with analog or digital sensing.
  • Four (4) dry contact SPDT relay outputs.
  • RS-485 four-wire data bus for networking to other Magic Modules and accessories, or to a personal computer.
  • Interface connection for X-10 Powerline control or for ELK Access Control module.
  • Four (4) Accumulator Counters, range 0 to 255.
  • Four (4) Timers, range 1/10 second to over 255 hours.
  • 16,384 program bytes using SIMPLE programming language.
  • EEProm “non-volatile” memory maintains program in the event of power loss.
  • MV480 400 Channel Recordable Voice Annunciator
  • Eight (8) minutes (480 seconds) of recordable audio.
  • Four hundred (400) addressable message channels.
  • On-demand playback.
  • Each message is 1.2 seconds in length but may be combined to produce longer messages.
  • Messages may be recorded via a built-in microphone or downloaded as .WAV files from a computer & ELK-129.
  • 24 Watt built-in audio amplifier with adjustable volume control.
  • ML8 Caddx Security Control Interface
  • Works with most Caddx NX Security Controls(except “E” series) and mounts directly into a Caddx NX6 or NX8 Box.
  • The ELK-930 performs three functions. It can detect ring activation from one or two doorbell buttons and a single telephone line. It conveniently isolates the voltage and current and produces an open collector (pull to ground) output which can be used to trigger an automation controller, relay, timer, etc. The circuit is pre-scored so that the individual detectors may be snapped off (separated) from each other. The ELK-930 Doorbell Detector monitors the current draw of a doorbell and produces an open collector output when the pushbutton is pressed and the doorbell draws 900mA or more. This open collector output can be used to trigger an automation controller input that utilizes high to low switching (pull to ground) for activation. The ELK-930 Telephone Ring Detector monitors the voltage on the telephone line and produces an open collector output (pull to ground) when the telephone ringing voltage is approximately 50 Volts or greater. The output follows the ringing pattern.

    Specifications:

    Max Input on Doorbell Boards: 24 Volts AC Nominal
    Max Output: 40mA @ 12 Volts D.C.
    Doorbell Detection Current: 900mA min.
    Size: 3.4" x 2.75" x .625"
    ELK MC100 Clock/Calendar Module ELK MT100 Temperature Sensor Module
    The ELK-MC100 Clock/Calendar is an accessory for the Magic Module programmable controller series. It can be used in a vast array of Clock & Calendar applications requiring Minute, Hour, Day, Weekday, and Monthly timing. It also provides an on-board connection for the Temperature Sensor Module(ELK-MT100) (optional). This board is plugged onto the Magic Module Accessory Connector(J1).

    Specifications:

    Operating Voltage: 5 Volts DC, supplied from ELK-MM443
    Current Draw: 200uA DC, supplied from ELK-MM443
    Battery: 3 Volt Lithium (CR2032)
    Size: 2.2" x 1.5" (60mm x 38mm)
    The ELK-MT100 Temperature Sensor permits the ELK Magic Module(ELK-MM443) program capable controller to monitor ambient air temperatures and control functions with programming. The Sensor can be distantly located up to 20' from the Module to an place where temperature measurement is required by you. The Sensor connects by means of a 4 conductor cable to the terminals of either the supplied Interface board or an ELK Clock/Calendar Module(ELK-MC100). This board is connected onto the Magic Module Accessory Connector(J1).

    Specifications:

    Temperature Resolution: -55C to +125C(-67F to 257) through 1° Celsius changes
    Operating Voltage: 5 Volts DC, supplied from ELK-MM443
    Current Draw: 1mA DC, supplied from ELK-MM443
    Compact Size: 2.4" x 2.3" x 1"
       
     
     
     

    Enter your email for a chance to WIN $100 Amex Gift Card.

    Please Enter Your Email Address

    *One entry per household please